BMPRO BatteryPlus35HA Скачать руководство пользователя | Manualshive

Страница: 50 / 60

background image

50

INTRODUCTION

RVView

monitors and displays vital battery information such as volts and amps,

charge/discharge status and details of the source input for your recreational vehicle
12V system.

RVView

is permanently wired into the

BatteryPlus35

in the recreational vehicle and

continuously monitors battery information, providing vital data at a glance using a
clear back-lit display.

Safety Precautions

Please read the Safety Precautions carefully before installing the unit.

Failure to observe these instructions properly may result in

property damage or personal injury, which may be serious

depending on the circumstances.

Refer to the installation section before operating. Correct installation is the most
critical factor in ensuring the safe use of the power supply. If every consideration
of these instructions has been satisfied the power supply will be safe to operate.
As this unit is powered by a communication cable it is critical that all connections
and cables are in a good and working order and properly connected.
Do not allow water or other liquids to enter the installation area.

CAUTION

Accessories

The following accessories are provided with

RVView

.

•

RVView

Unit

•

RVView

Manual

• 4 Mounting Screws

About RVView

The

RVView

is a display unit that connects to

BatteryPlus35

and displays battery or

system information. Its backlit LCD displays information includes:

•  System voltage
•  Input and output current
•  Battery charging and discharging indicator
•  Power Source – Mains, Solar or Car
•  Warning indicator
•  Battery charge status
•  Back-light which turns on for 30 seconds

«
...
48
49
50
51
52
...
»

Содержание BatteryPlus35HA





























































Отзывы:

Нет отзывов

Похожие инструкции для BatteryPlus35HA

Бренд: Parallel Audio Страницы: 4

Бренд: Fieldmann Страницы: 52

Бренд: Schumacher Страницы: 36

Pump In Style Battery Pack

Бренд: Medela Страницы: 2

Intellicharger i4

Бренд: Sysmax Страницы: 1

Бренд: Bretford Страницы: 9

Бренд: CE-Link Страницы: 6

Бренд: YATO Страницы: 64

Бренд: Samlex Europe Страницы: 22

Бренд: ring Страницы: 16

Бренд: Schumacher Electric Страницы: 56

ELPSM2 Light-Pak

Бренд: Eaton Страницы: 6

Бренд: Armytek Optoelectronics Страницы: 2

Бренд: hager Страницы: 4

Elite PRO CBHF2-PFC

Бренд: BTI Страницы: 12

Бренд: UNIROSS Страницы: 4

OpenScape WLAN Phone WL4

Бренд: Unify Страницы: 101

Бренд: RIDGID Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды