BMPRO BatteryPlus35HA Скачать руководство пользователя | Manualshive

Страница: 47 / 60

background image

47

Press and release the button a few times until you see ADVANC
To exit menu, keep pressing the “Back” button until the home screen is seen.

WARNING

The advanced menu is reserved for technical personnel
only and available features vary with some versions of
the BatteryPlus35.

APPENDIX 1 : ADVANCED MENU

Incorrect use of this menu can over charge the battery and cause damage to
property and cause personal injury. If unsure, do not change the default values.

The advanced menu allows installers to fine tune the charging parameter, such as
bulk voltage, bulk time and float time.

Advanced Menu Entry

Press and hold the button until you see SETUP

Bulk Voltage

The bulk voltage is the maximum voltage at which the battery will be charged. This
voltage can be adjusted from 13.6V to 14.6V with increments of 0.1V.

Appendix 1: Advanced Menu

Advanced Menu

WARNING!!!! The advanced menu is reserved for technical personnel only. This
menu is not available for all revisions of the BatteryPlus35.

Incorrect use of this menu can over charge the battery and cause damage to
property and cause personal injury. If unsure, leave as default. Default values can
vary between revisions.

The advance menu allows installers to fine tune the charging parameter, such as
bulk voltage, bulk time and float time.

To exit menu, keep pressing the “Back” button until the home screen is seen.

Bulk Voltage

This is the maximum voltage at which the battery will be charged. This voltage
can be adjusted from 14.0V to 14.4V with increments of 0.1V.

To exit menu, keep pressing the “Back” button until the home screen is seen.

Bulk Time

This is the maximum time the bulk voltage can be applied to the battery.

To exit menu, keep pressing the “Back” button until the home screen is seen.

27

To exit menu, keep pressing the “Back” button until the home screen is seen.

«
...
45
46
47
48
49
...
»

Содержание BatteryPlus35HA





























































Отзывы:

Нет отзывов

Похожие инструкции для BatteryPlus35HA

Бренд: Sibata Страницы: 4

Бренд: Tactical Страницы: 2

Volt CPAP Battery Pack

Бренд: Viverity Страницы: 2

Бренд: Prestigio Страницы: 72

Eve Plus 0131-CC

Бренд: Basalte Страницы: 2

Бренд: APA Страницы: 32

eVault Max 18.5

Бренд: Fortress Power Страницы: 2

Smart Station S

Бренд: ALIGATOR Страницы: 28

Бренд: AEenergy Страницы: 11

Бренд: Radio Shack Страницы: 2

Бренд: Makita Страницы: 60

Бренд: Hilti Страницы: 9

Бренд: Aukey Страницы: 32

Бренд: AEG Страницы: 31

Бренд: AEG Страницы: 100

Бренд: AEG Страницы: 60

Бренд: AEG Страницы: 31

Бренд: AEG Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды