BMPRO BatteryPlus35HA Скачать руководство пользователя

Страница: 15 / 60

Remote Load-Isolator Switch Connection

BatteryPlus35

allows for remote control of the load connections by two methods,

remote switch via the

Trek

display (optional accessory) and hardware remote switch

terminals. All loads can be turned off by operation of either switch. This feature can
be used to store the caravan when not used.

Both methods are described below. If both methods are installed, the dedicated
remote switch overrides the remote switch via

Trek

Remote Switch via Trek Display

The load outputs on

BatteryPlus35

can be controlled via

Trek

(purchased

separately).

Trek

has a dedicated button to switch all loads off and on. When the

loads are OFF the unit enters into ECO mode.

Battery charging is not affected by this switch.

For detailed information and more, see page 31.

Note:

This function is not available on the

RVView

Remote Switch via Hardware Remote Switch Terminal (RSW)

A pair of contacts, item

in Name and Function of Parts, are provided for

connection to the external switch. When this switch is shorted, all loads are
disconnected from all power and the unit is put into storage mode.

Battery charging is not affected by this switch.

Any accessories connected to the communication bus are turned off.

Any convenient switch and wire size may be used.

Communication Bus Connection

The communication bus connection is used to connect the

BatteryPlus35

and

external BMPRO accessories via a data cable.

Note:

See the BMPRO by Setec website for cable accessories.

Installing Controllable Pumps

The

BatteryPlus35

has a feature which enables two output channels to be remotely

controlled from the

Trek

unit. These outputs are used to control two pumps which

can only be switched ON and OFF, if installed. The pumps have to be connected to
outputs and . If only one pump is required to be controlled, connect it to output
Figure 3: DC Wiring Diagram for

BatteryPlus35SR

and

BatteryPlus35HA

and Figure

4: DC Wiring Diagram for

BatteryPlus35PM

shows a single pump connected.

Содержание BatteryPlus35HA





























































Результаты поиска

Содержание BatteryPlus35HA

Отзывы:

Похожие инструкции для BatteryPlus35HA

Бренды по названию

Популярные бренды

BMPRO BatteryPlus35HA, Системное руководство

Результаты поиска

Содержание BatteryPlus35HA

Отзывы:

Похожие инструкции для BatteryPlus35HA

Бренды по названию

Популярные бренды