BMPRO BatteryPlus35HA Скачать руководство пользователя | Manualshive

Страница: 18 / 60

background image

18

Battery Connection / Disconnection Procedure

WARNING

Sparks have the potential to cause an explosion should
combustible gases be present. The following procedures
are designed to minimise the risk of spark generation
while connecting or disconnecting the battery. The
positive terminal of the battery must not be connected to
the chassis of the vehicle.

Battery Disconnection Procedure

The caravan battery should be disconnected as per the following steps.

1. Remove mains power to the

BatteryPlus35

2. Disconnect Solar and Aux inputs from the

BatteryPlus35

3. Turn off all 12 V equipment connected to

BatteryPlus35

4. Disconnect the negative battery terminal
5. Disconnect the positive battery terminal

Battery Connection Procedure

The caravan battery should be connected as per the following steps.

1. Confirm no mains power, auxiliary power, or solar power is connected to the

BatteryPlus35

2.  Connect the positive battery terminal
3.  Connect the negative battery terminal
4.  If a

Trek

is installed, set the total battery capacity (refer page 31) to ensure

accurate forecasting

«
...
16
17
18
19
20
...
»

Содержание BatteryPlus35HA





























































Отзывы:

Нет отзывов

Похожие инструкции для BatteryPlus35HA

Бренд: La Marche Страницы: 45

Бренд: MOB Страницы: 8

Бренд: Raider Страницы: 12

Certa CTMWR40CHAA

Бренд: Kogan Страницы: 12

Бренд: LEGRAND Страницы: 4

eVault Max 18.5

Бренд: Fortress Power Страницы: 2

Бренд: Purkeys Страницы: 24

Бренд: Wentronic Страницы: 8

pebble VCC-A008-PBP-XT

Бренд: Veho Страницы: 2

Бренд: Inateck Страницы: 20

Бренд: Magnetek Страницы: 6

BOLT ACDC 58830

Бренд: Halo Страницы: 18

Бренд: Schumacher Electric Страницы: 12

Бренд: Bolt Страницы: 20

Бренд: Callpod Страницы: 19

Бренд: Power Craft Страницы: 24

LESTRONIC II 13110

Бренд: Lester Страницы: 6

Бренд: Lester Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды