Blue Seal G91 Скачать руководство пользователя страница 31

Страница: 31 / 33

Appendix B: Gas Conversion

Moffat Ltd, January 2007

Revision 1/

Blue Seal Evolution Series Gas Salamander

Conversion Procedure

NOTE:

•

These conversions should only be carried out by qualified persons. All connections
must be checked for leaks before re-commissioning the appliance.

•

For all the following conversion instructions, the side panels have to be removed
(Remove the two screws at the bottom of each side panel).

•

All conversion details apply to both L/Hand and R/Hand burners.

•

For all relevant gas specifications refer to the table at the end of this section.

Main Burner Injectors

Unscrew the main burner injectors (

” A/F).

Determine the correct injector sizes for the corresponding gas

type from the rating plate affixed to the right hand side panel
front bottom corner.

Replace with the correct size injectors.

Pilot Injectors

Unscrew the cap from the rear of the pilot burners, and unscrew

the pilot injectors (taking care not to lose the springs).

Determine the correct pilot injector sizes for the corresponding
gas from the rating plate affixed to the right hand side panel
front bottom corner.

Replace with the correct size pilot injectors.

NOTE: Ensure that the Pilot Injectors are fully screwed in.

AUTION

Ensure that the Unit is isolated from the gas supply before commencing
servicing

Main Burner

Injector

Pilot Injector Cap

Fig B2

Fig B1

Содержание G91


































Результаты поиска

Содержание G91

Отзывы:

Похожие инструкции для G91

Бренды по названию

Популярные бренды

Blue Seal G91, Руководство по обслуживанию

Результаты поиска

Содержание G91

Отзывы:

Похожие инструкции для G91

Бренды по названию

Популярные бренды