Blonder tongue AQT8-IP Скачать руководство пользователя

Страница: 17 / 44

AQT8-QAM/IP

User Manual

Section 5 – Communicating with the Unit

Local or remote communication with the unit is only possible through a GUI-based menu via any standard web browser.

Before you can communicate with the unit, you must configure the unit's IP address to conform with your existing IP

network or LAN. To do so, follow these steps:

(1)

Plug one end of the Ethernet cable that is provided in the hardware bag to unit’s rear-panel RJ45 interface marked

“10/100 Remote Control”. Plug the other end of the cable to your computer.

(2)

The factory default IP address of the unit is

172.16.70.1

. To be able to communicate with the unit, you must first change

your computer's IP address.

The following steps explain how to do this for a computer with

Windows XP

operating software:

(a)

On your computer, open the "Control Panel"

(b)

Double-click on "Network Connections"

(c)

Right-click on the "Local Area Connection", and then click on the "properties".

(d)

A dialog box entitled "Local Area Connection Properties" will appear. In this box, double-click on the "Internet

Protocol (TCP/IP)".

(e)

A dialog box entitled "Internet Protocol (TCP/IP) Properties" will appear. Select the "Use the following IP address"

option and enter the following addresses:

IP address: 172.16.70.2
Subnet mask: 255.255.255.0

No need to enter a value for the Default Gateway.

Click OK to close the dialog box. Now your computer is ready to communicate with the unit.

- OR -

The following steps explain how to do this for a computer with

Windows 7

operating software:

(a)

On your computer, open the "Control Panel"

(b)

Click on “Network and Internet”

(c)

Click on the "View network status and tasks"

(d)

Click on “Change Adapter Settings” on left hand side of the window

(e)

Right-click on the "Local Area Connection", and then click on the "properties".

(f)

A dialog box entitled "Local Area Connection Properties" will appear. In this box, double-click on the "Internet

Protocol Version 4 (TCP/IPv4)".

(g)

A dialog box entitled "Internet Protocol Version 4 (TCP/IPv4) Properties" will appear. Select the "Use the following

IP address" option and enter the following addresses:

IP address: 172.16.70.2
Subnet mask: 255.255.255.0

No need to enter a value for the Default Gateway.

Click OK to close the dialog box. Now your computer is ready to communicate with the unit.

Содержание AQT8-IP













































Результаты поиска

Содержание AQT8-IP

Отзывы:

Похожие инструкции для AQT8-IP

Бренды по названию

Популярные бренды

Blonder tongue AQT8-IP, Руководство пользователя

Результаты поиска

Содержание AQT8-IP

Отзывы:

Похожие инструкции для AQT8-IP

Бренды по названию

Популярные бренды