manualshive.com logo in svg

Blonder tongue AQT8-IP, Руководство пользователя

Поделиться
Скачать
Blonder tongue AQT8-IP Скачать руководство пользователя страница 33

33

AQT8-QAM/IP 

User Manual

12

13

14
15
16
17
18
19
20

21

22

23
24

25

26

Remember

 

to

 

click

 

on

 

the

 

SAVE

 

button

 

to

 

apply

 

the

 

new

 

values/configurations.

6.11 "Admin" Screen (continued)

11

Using the “Static until DHCP” setting when the 

DASHBOARD is not being used

 may cause communications problems 

should a DHCP server ever be present on the IP control network.  
In case the unit picks up a DHCP address and can no longer be communicated with because of an unknown IP address  

assigned,  do the following:

1.  Disconnect the unit from the IP network.

2. 

Reset the IP via the front panel button 

3.  Access unit via default IP address (172.16.70.1).

4. 

Go to Admin page and change  Control Port DHCP to “Static”.

5.  Enter in a Control Port IP address based on network requirements.

Control Port IP Address:

   is the static IP address that is assigned to the unit. It allows the user to access the unit via 

the web interface. (Factory Default: 172.16.70.1 )

Control Port Subnet Mask:

 is the Subnet Mask address of the unit. It allows the user to access the unit from  

another network via the web interface.  (Factory Default:  255.255.255.0 )

Control Port Default Gateway:

 

 

is the gateway address of unit. It allows the user to access the unit from another  

network via the web interface. (Factory Default:  172.16.70.254 )

EAS Port IP Address:

  Is the static IP address assigned to the IP EAS Port.  (Factory Default: 192.168.252.2 )

EAS Port Subnet Mask:

 is the subnet mask address of the IP EAS port.  (Factory Default: 255.255.255.0 )

EAS Port Default Gateway: 

Is the gateway address of the IP EAS Port.  (Factory Default: 192.168.252.254 )

GigE Port IP Address:

  is the static IP address assigned to the Gigabit Ethernet (GigE) port. (Factory Default: 192.168.253.1 )

GigE Port Subnet Mask:

 is the subnet mask address of the GigE port.  (Factory Default: 255.255.255.0 )

GigE Port Default Gateway: 

Is the gateway address of the GigE Port.  (Factory Default: 192.168.253.254 )

Event Log Destination:

  is the IP address of the remote server, to which Syslog sends the activities recorded by the 

unit for monitoring and troubleshooting purposes. (Factory Default: 172.16.70.2 )

Log Destination Port #:

  is the Error Log Destination port to which a duplicate of the error messages created by the 

unit can be forwarded for monitoring and troubleshooting purposes. 

 (Factory Default: 514 - unmodifiable)

Time Server IP:

   is the IP address for the Time Server from where the unit can obtain its clock reference. See Section 

6.1.2 for details. (Factory Default: 172.16.70.2 )

Syslog Errors:

 is to enable/disable forwarding error messages (in red font) to a Syslog. 

(Factory Default: Disabled)

Syslog Informational:

  is to enable/disable the unit to forward information messages (in blue font) to a Syslog. 

(Factory 

Default: Disabled)

Syslog Feedback: 

is to enable/disable the unit to forward feedback or confirmation messages (in green font) to a 

Syslog. (Factory Default: Disabled)

Average Bit Rate: 

 The factory default for this option is "Disabled". The 

“Enabled” setting should only be used when 

incorrect bitrate information is specified in the video header as received from the broadcaster.  Incorrect declared 

bitrates from the broadcaster may cause overload/ buffer issues affecting the output TS. The “Enabled” setting  allows 

the unit to assign an alternate bitrate instead of what’s declared in the input TS.
Once Average Bit Rate is set to "Enabled", go to          in section 6.3 (p.22) , and follow the instructions in order to 

complete enabling of this feature.

15

Содержание AQT8-IP













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды