background image

Blichmann Engineering, LLC   2015 

                                                                                                                          

 For replacement parts visit blichmannengineering.com/genuine-replacement-parts

 

 

     

  

 
 

When you have finished installing a leg on all 4 sides of the mast, place it upright on the floor.  Using a 
carpenter’s level as shown in Fig 5, level the product on all sides using the adjustable leveling feet.  Ensure 
that each leveling foot is touching the hard floor so it does not rock.   The assembly of the base stand is now 
complete!   

 
 

 

   

 

 

Danger!:

 ALWAYS ensure that the mast rests firmly on the hard surface as shown in Fig 6!  This allows the 

weight from the pots to be borne by the mast instead of the legs.  Failure to have the mast resting on the floor 
will add excessive load to the legs possible leading to failure and severe personal injury from burns and falling 
objects!! 

 
Assembling the Burner Tiers 
 

Each burner is shipped with all legs assembled.  To mount it onto the mast, the arms (1LH, 1RH) and the 
torsion brackets (1RH, 1LH) must be assembled prior to installing them on the mast of the stand.  Begin by 
installing the torsion brackets to one of the legs on the burner frame as shown in Fig 7.   
 

Tip:

 Leave all fasteners finger tight at first which will ease assembly onto the mating parts.  You can tighten all 

the fasteners once you have the burner tier fully assembled. 

Fig. 6 

Fig. 5 

Fig. 3 

Fig. 4 

Must rest on floor! 

Содержание TopTier















Отзывы: