Blichmann TopTier Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 14

Blichmann TopTier Скачать руководство пользователя страница 3



Blichmann Engineering, LLC 2015

For replacement parts visit blichmannengineering.com/genuine-replacement-parts

3

Shelf Tier (per shelf ordered)

1 - Stainless shelf
2 - Stainless angle brackets
8 - Stainless #10 screws and nuts

Tool List:

The following basic tools are required to assemble the stand and are not included with the product:



7/16”, 1/2” and 9/16” wrenches (for the legs, tier arms, wheels, and burner brackets)



10mm and 17mm

(or 11/16”) wrenches (for the pot retaining bars, and installing burners on tier arms)



Adjustable wrench



Torque wrench for tightening the arms and legs



#2 Phillips head screwdriver

and 3/8” open end wrench (for optional shelf tier)



Optionally, socket wrenches of the above size will speed assembly.

Assembling the Stand

Begin assembly by locating a flat, level hard surface to work on such as a concrete surface or hard floor.
Install the t-

slot plates on the legs using the 5/16” hardware. Note that the washers are installed between the

head of the bolt and the inside surface of the leg. You will need to install 2 plates on each leg. Next, thread a
leveling foot in each leg as shown in Fig 2.

Caution:

ALWAYS use the washer between the head of the bolt and the leg. Failure to use the washer will

cause the bolt to penetrate too deeply into the t-slot and possibly damage the extrusion.

Tip:

Thread the bolt into the t-slot plate only about 1 turn

– this will make it easier to install the leg on the

aluminum mast where it will be positioned and tightened fully.

Install each leg onto the extrusion by sliding the plates into the mating slot on the mast as shown on Fig 3.  Be
sure to install it 1.5” above the bottom of the mast as shown in Fig 4.  Tightening the nut snugly (20 ft-lb or 27
N-m) using a torque wrench.

Caution:

Excessive tightening may permanently deform the mast.

Fig. 1

Washer
This Side

Fig. 2

Washer
this Side

«
1
2
3
4
5
...
»

Содержание TopTier















Отзывы:

Нет отзывов