BLH NOBEL G5 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 32

BLH NOBEL G5 Скачать руководство пользователя страница 5

G5 Weighing Instrument

1-1

1. Introduction

General

The G5 Instruments are high performance single-channel weight indicators (PM model,
panel mounted) or weight transmitters (RM model, DIN rail mounted) intended for
industrial systems. This manual describes the functionality of the optional Fieldbus
interface of the G5 Instrument. The instrument supports the following busses:
ProfibusDP, DeviceNet, ControlNet and EtherNet/IP. The optional fieldbus module is
mounted in the Fieldbus slot.

l fieldbus settings are done with setup parameters in the instrument. No settings are
done on the module itself.

Module installation

Make sure the instrument power supply is off or disconnected. Remove the plastic
cover from the fieldbus slot. Insert the adaptor

very carefully and make absolutely

sure that the adaptor slides correctly into the guides

in the connector on the PCB.

Tighten the two fastening screws at the adaptor front and check that the two securing
hooks locks into the PCB.

Module type

Connector

Baud rate

Address

Bus Supply

Voltage

Profibus-DP

Profibus
9-pin, female
D-sub (DB9F)

9.6 kbps –
12 Mbps or
Auto set by
parameter

1 – 125,
set by parameter

DeviceNet

5 pin male
connector.

125, 250,
500 kbps or
Auto set by
parameter.

0 – 63,
set by parameter

According to
DeviceNet (Node)
specification:
nominal 24 VDC,
range 11 – 25
VDC.

ControlNet

BNC.

Fixed 5
Mbit/s.

1 – 99, set by
parameter

EtherNet/IP

Dual RJ45
(Only port 1
,P1) is
supported

Selectable Static
or DHCP. If static
choosen IP-
address, Net
Mask and Default
Gateway are set
by parameters.

«
...
3
4
5
6
7
...
»

Содержание G5

































Отзывы:

Нет отзывов