BLH NOBEL G5 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 32

BLH NOBEL G5 Скачать руководство пользователя страница 12

Technical Manual

2-6

EtherNet/IP Module

ControlNet module front view

(1) Network Status LED.

(2) Module Status LED.

(3) Link/Activity Port 1.

(4) Link/Activity Port 2.

Network Status LED

LED State

Indication

Off

No power or no IP address

Green

Online, one or more connections established (CIP class 1 or 3)

Green, flashing

Online, no connections established

Red

Duplicate IP address, fatal error

Red, flashing

One or more connections timed out (CIP class 1 or 3)

Module Status LED

State

Indication

Off

No power

Green

Controlled by a Scanner in run state

Flashing Green (1 Hz)

Not configured or Scanner in idle state

Red

Major fault (EXCEPTION state, fatal error etc.)

Flashing Red (1 Hz)

Recoverable fault(s)

Link/Activity LED 3/4

State

Indication

Off

No link, no activity

Green

Link (100 Mbit/s) established

Green, flickering

Activity (100 Mbit/s)

Yellow

Link (10 Mbit/s) established

Yellow, flickering

Activity (10 Mbit/s)

NS

MS

EtherNet/IP

(1)

(2)

(3)

(4)

P1 P2

«
...
10
11
12
13
14
...
»

Содержание G5

































Отзывы:

Нет отзывов