BLH NOBEL G5 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 32

BLH NOBEL G5 Скачать руководство пользователя страница 21

G5 Weighing Instrument

5-7

Scale Status

Bits set to 1 in this register have the following meaning:

Bit no Function

Comment

0

Not used

Not used in the fieldbus interface

1

Not used

Not used in the fieldbus interface

2

Not used

Not used in the fieldbus interface

3

Good zero (disp. weight)

4

Good zero Gross

5

Good zero Net

6

Net Mode

'1' = Net mode

‘0' = Gross mode

7

Motion

Unstable weight

8

Not used

9

Not used

10

Not used

11

Flow rate display

Flow rate is shown in the display.

12

Net weight > 6 digits

The net weight value is out of precision and
should normally not be used.

13

Gross weight > 6 digits

The gross weight value is out of precision and
should normally not be used.

14

Not used

15

Not used

Gross weight

The gross weight value consists of 4 bytes. The weight should

not

be read alone

because the status and error codes are stored in other registers. The weight is only
valid when the register ‘Scale Error code’ equals 00. Gross weight can be in integer
format or floating point format depending on the setting. The number of decimals
used in the gross weight can be read in byte 88.

Net weight

The net weight value consists of 4 bytes. The weight should

not

be read alone

because the status and error codes are stored in other registers. The weight is only
valid when the register ‘Scale Error code’ equals 00. Net weight can be in integer
format or floating point format depending on the setting. The number of decimals
used in the net weight can be read in byte 88.

«
...
19
20
21
22
23
...
»

Содержание G5

































Отзывы:

Нет отзывов