Blease Sirius 1000 Скачать руководство пользователя страница 99

Страница: 99 / 107

First Line and Planned Maintenance Manual

Frontline Sirius®

7.9 Bellows Base/Cover (9)

•

Remove the bellows cover (bayonet fitting) and then replace the bellows base/cover ‘O’ Ring

(9).

•

Remove the bellows by gently pulling the lower convolution of the retaining ring.

•

Remove the pop-off valve.

•

Replace the white bellows base/pop-off (11)

7.10 Pop-off Valve (15)

•

Undo the two screws that hold the pop-off valve cover and support ring together.

•

Replace the diaphragm valve (15).

Figure 11 Pop-off Valve

•

Replace Pop-off valve in bellows base.

•

Refit bellows by gently pulling the lower convolution over the ring in the bellows base.

•

Replace the bellows outer cover.

Diaphragm Cover

Diaphragm Support Disc

Diaphragm
Assembly
Pop-off Valve

Screw

Nut and Washer

Diaphragm with hole

Diaphragm Brace

PEEP Valve Weight

Sealing

Disc

NOTE:
TORQUE SCREW ITEM 5
IN POSITION TO O.40 N

APPLY TAMPER EVIDENT SEAL
TO JOINT OF SCREW AND DISC

7. Fitting Planned Maintenance Kits

Содержание Sirius 1000












































































































Результаты поиска

Содержание Sirius 1000

Отзывы:

Бренды по названию

Популярные бренды

Blease Sirius 1000, Руководство пользователя

Результаты поиска

Содержание Sirius 1000

Отзывы:

Бренды по названию

Популярные бренды