Blease Sirius 1000 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 107

Blease Sirius 1000 Скачать руководство пользователя страница 8

7

First Line and Planned Maintenance Manual

Frontline Sirius®

Product Improvement

Blease Medical Equipment Limited has a policy of continued product improvement and
therefore reserves the right to make changes which may affect the information contained
in the manual without giving prior notice.

Responsibilities of the Manufacturer

The manufacturer accepts responsibility for the effects on safety, reliability and performance of
the equipment only if:

•

assembly operations, extensions, adjustments, modifications and repairs are

carried out by persons with written authorisation from the manufacturer;

•

the equipment is used in accordance with the instructions for use;

•

the electrical installation of the relevant room complies with the ‘Regulations for
the Electrical Equipment of Buildings’.

NB
If during the warranty period the equipment is serviced by an unauthorised
party, the warranty will be void.

Disclaimer

Opening of the control unit by unauthorised personnel automatically voids all warranties and
specifications. The prevention of tampering is solely the user's responsibility; the manufacturer
assumes no liability for any malfunction or failure of the ventilator if the control unit is opened.

The instructions in this manual assume that the engineer is familiar with and has
had training in the servicing and care of anaesthetic equipment and is able to use
pressure gauges, flowmeters and other laboratory equipment.

Blease accept no responsibility or liability for any patient injury or adverse
circumstances which may arise from unauthorised maintenance of Blease Frontline
Sirius Machines.

«
...
6
7
8
9
10
...
»

Содержание Sirius 1000












































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды