manualshive.com logo in svg

Blease Sirius 1000, Руководство пользователя

Поделиться
Скачать
Blease Sirius 1000 Скачать руководство пользователя страница 45

44 

First Line and Planned Maintenance Manual  

Frontline Sirius® 

 

2.9     CHECKLIST FOR ANAESTHETIC EQUIPMENT 2003 

          The following checks should be made prior to each operating session. In addition, 
          checks 2, 6 and 9 (Monitoring, Breathing System and Ancillary Equipment) should 
          be made prior to each new patient during a session. 
           

1.       Check that the anaesthetic machine is connected to the electricity supply 

          (if appropriate) and switched on. 

          Note:   Some anaesthetic workstations may enter an integral self-test programme when 
          switched on; those functions tested by such a programme need not be retested. 
 

      Take note of any information or labelling on the anaesthetic machine referring to the 
      current status of the machine.  Particular attention should be paid to recent servicing.  
      Servicing labels should be fixed in the service logbook. 

 

2.       Check that all monitoring devices, in particular analyzer, pulse oximeter 

          and capnograph, are functioning and have appropriate alarm limits. 

 

•     

Check that gas sampling lines are properly attached and free of obstructions. 

•     

Check that an appropriate frequency of recording non-invasive blood pressure is 

selected. 

      (Some monitors need to be in stand-by mode to avoid unnecessary alarms before being 
      connected to the patient). 
Oxygen Monitor Test

 

      The Oxygen Calibration menu allows adjustment of the displayed oxygen concentration 
      to match the gas that the probe is exposed to; this is normally 100% pure oxygen. 

 

NOTE: Calibration is only possible if the ventilator is in Standby and a probe is 

connected. 

 

•     

Press the Main menu key, select Oxygen Calibration. 

•     

Expose the probe to 100% pure oxygen flow or 21% room air. 

•     

Adjust the displayed value to 100% or 21% as applicable by turning and pressing the 

Trak wheel. 

•     

Press the Trak wheel again to start the calibration process. This takes approximately one 

minute and a countdown is displayed whilst it is in progress. 

 

2. User Pre Use Testing 

Содержание Sirius 1000












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды