manualshive.com logo in svg

Blease Sirius 1000, Руководство пользователя

Поделиться
Скачать
Blease Sirius 1000 Скачать руководство пользователя страница 66

65 

First Line and Planned Maintenance Manual  

Frontline Sirius® 

 

4.1.6    Patient Airway Flow Sensor 

The flow sensor can be hand or machine washed and disinfected with a suitable disinfectant. 
Steam autoclaving 

must not exceed 

134

o

C. The sensor can be sterilised with ethylene oxide. 

To clean the flow sensor, pour distilled water slowly and gently into the outlet port. Water must 
not be directed into this port under pressure.  

 

Chemical decontaminants or liquid sterilisation agents will damage the sensor 

and must NOT be used for cleaning or sterilising. If autoclaving the sensor, the 

autoclave must only be used with distilled water. 
 

4.1.7    Blanking cap on patient flow sensor is NOT autoclavable. 

 

Bellows 

Only the bellows base and the parts inside the bellows require sterilisation. 

 

To avoid damage to the equipment: 
Peak sterilisation temperature must not exceed 134ºC. 
Do not sterilise the control unit.  
Gas sterilisation should be followed by quarantine in a well-ventilated area to 

allow dissipation of residual absorbed gas. 
Follow the sterilisation agent manufacturer's instructions. 
The expiratory valve must be disassembled prior to autoclaving to prevent the 

occurrence of clamping stresses. 

 

The paediatric adapter, can be sterilised but must not be autoclaved. 

 

1.   Pull absorber forward to disconnect the bellows base. 

2.   Loosen the two thumb screws retaining the bellows base and remove the bellows base 
      and housing from the control unit. 

3.   Remove the pop-off valve and paediatric bellows adapter (if fitted) and clean and   sterilise 
      them separately. 

4.   Perform sterilisation as specified in the table opposite. 

4.  Maintenance 

Содержание Sirius 1000












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды