8
Contact with eyes: Immediately flush eyes with cold, fresh water for a minimum of 15 minutes. Seek
professional medical attention.
k)
Do not eat, drink or smoke near the hydraulic oil.
l)
HV46 hydraulic oil holds no danger of intoxication.
m)
The hydraulic oil is stable at normal temperatures for storage, handling and use. However, the hydraulic
oil is flammable when exposed to certain conditions. Empty containers may contain flammable or
explosive vapors. Rags that are soaked with the product and paper or materials which have been used
for absorbing the spilled product are inflammable. Make sure that no accumulation occurs. Remove
safely after use.
n)
Avoid sparks, open flames, extremely high temperatures and other sources of ignition.
o)
Consult the Safety Data Sheets for additional information regarding the hydraulic oil.
p)
Oil-level should be half the glass of the level indicator.
If you don’t see the oil in the indicator, the level
is too low. If the level is above the glass, the level is too high.
q)
Only use HV46 hydraulic oil (E00481), non-compatible fluids could cause damage to the unit or serious
injury.
r)
Once a year the oil from the system and the filter should be replaced.
s)
Work on hydraulic equipment or operating materials may only be undertaken by a skilled hydraulic
engineer or by trained persons under the guidance and supervision of a skilled hydraulic engineer as well
as in accordance with the hydraulic engineering regulations.
t)
Hoses and pipe work can be under high hydraulic pressure. The temperature can be above 37° C. Use
only hoses and pipe work that are sized and marked in accordance with the overall power consumption
of the machine.
u)
A second person must be deployed who can disengage the hydraulics in an emergency if work on live
parts is necessary. The work area must sealed off using a red and white safety chain and a danger sign.
For the electrical parts, use a tool that is insulated against voltages.
v)
Do not
open
or
remove protective guards
while driving gears are running.
w)
If safety-critical changes occur to the machine or its working method, the machine must be shut down
immediately! The cause of the fault must be established, and rectified.
x)
In the event of operational malfunctions the machine must be shut down immediately and secured!
3.7
Battery safety
a)
Only use Blastrac approved batteries. Blastrac cannot guarantee the safety of the machine when other
batteries are used.
b)
Every service work on batteries should only be done by trained personnel.
c)
The battery contains lead-acid, do not disassemble, heat above 60°C, or incinerate.
d)
Immediately flush eyes with cold, fresh water for a minimum of 15 minutes if electrolytic acid comes in
contact with eyes. Seek professional medical attention immediately.
e)
For work with the battery you need to remove all metal jewelry like rings, watches, necklaces etc. They
can be a cause of serious burns.
f)
The old battery should be recycled. Batteries contain harmful materials, like lead en sulphuric acid.
These materials form an environmental and health hazard. Therefore it is imperative that they are
recycled responsibly in accordance with local disposal and environmental regulations.
3.8
Transport safety
a)
NEVER lift machine with mounted tool! This sharp tool can be very dangerous!
b)
Be aware of your surroundings and machine operating level. Do not side hill, do not run on steep incline,
this could cause machine to tip over.
c)
The weight of the BMS-220 is 1080 kilogram. Use preferably appropriate appliances as a lift, crane or
forklift. Use the existing lifting points to lift the machine, use the brackets on the bottom when using a
forklift.
d)
Before every use check the lifting eyes/lugs and welds for:
deformation, damages, cracks, corrosion and wear.
e)
Each lifting lug has a WLL of 1500kg (3300 lbs.), only li
ft the machine as shown in the picture…
f)
When lifting the machine from the ground, always use the lowest lifting speed. The cables must first be
tensioned at this speed; they must not be slack when the machine is lifted from the ground.
g)
During hoisting make sure to be at a safe distance from the machine with the most optimal view on the
machine and working environment.
h)
Never stand directly below the machine.
i)
The lifting eyes/lugs can also be used to fasten the machine on a pallet or during transport.
Содержание BMS-220 ADB
Страница 11: ...11...
