6
3. Safety
Warning!
Read all safety warnings and all instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire, explosions and / or serious injuries.
It is the responsibility of the user to analyse the surface to be treated. The surface may not
contain any substances which could pose a fire-, explosion- or health risk when treated. The user should make
a risk assessment on the basis of the information obtained about the surface to be treated and take proper
precautions for the work to be performed.
In case of any inappropriate usage, improper operation or repair, the producer shall be exempt from liability.
3.1
Work area safety
a)
Do not use the machine in rain, damp or wet locations.
b)
Avoid dangerous environments: do not work in the presence of explosive atmospheres, in the presence of
flammable liquids, gases or dust. Remove materials or debris that may be ignited by sparks.
c)
Make sure there is enough ambient light on the work area. Cluttered or dark areas invite accidents.
d)
Keep children and bystanders away while operating the machine. They are likely not to foresee the
potential dangers of the machine. Distractions could cause you to lose control of the machine.
e)
Persons who are not operating the machine must not be permitted to stay in the surrounding area of at
least 5 meter from the machine.
f)
Never use the machine when the surface is not clear and if there is a risk of stumbling or tripping.
g)
Make sure that there is nothing standing or situated on the surface to be treated.
h)
Remove all objects from the surface that can damage the machine. Remove reinforcing steel or other
objects protruding from the surface in order to prevent damage to the machine.
i)
Warning! Make sure that the surface to be treated does not contain dangerous materials such
as:
- combustible or explosive dusts or substances.
- carcinogenic or pathogenic substances.
In these cases, additional safety measures should be used. Always mind the local safety requirements.
Contact your dealer for additional options.
j)
Make sure that there are no cables or hoses in the driving direction of the machine.
k)
Effective organizational measures must be taken to prevent that employees are present in the work area
of this machine. If this is not possible,
effective traffic rules must be adopted.
l)
If the proper execution of the work requires the presence of workers in the work zone, it is mandatory to
take effective measures to prevent them from being injured by the machine.
m)
It is forbidden to use/drive the machine on public roads, pavements, etc. unless they are closed off from
the general public and other traffic.
3.2
Electrical safety
a)
Use only extension cables for extending the charger cable that are sized and marked in accordance with
the overall power consumption of the machine. Do not use damaged extension cables.
b)
Electrical cables must be rolled entirely off of the reels.
c)
Any damage to the electric cables and/or electrical components is not permitted.
d)
The voltage on the identification plate must comply with the power supply.
e)
Use an electrical power supply connection with earth connection and earth leakage circuit breaker.
f)
Keep the machine original; The machine is always equipped with an earthed connection, do not
change this
and always use earthed cables with an earthed plug.
g)
Inspect and test the electrical components regularly. The electrical components have to satisfy with the
requirements set out in the harmonised norm EN60204-1.
h)
Always call a skilled electrician or your distributor when you have questions about the safety of the
electrical components.
i)
Work on electrical equipment or operating materials may only be undertaken by a skilled electrician or by
trained persons under the guidance and supervision of a skilled electrician as well as in accordance with
the electrical engineering regulations.
j)
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the machine. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
k)
Be careful with water on the treated surface. Electrical cables must not come into contact with water.
l)
Pull out the main plug of the charger and switch the contact to the OFF-position on the electrical panel
during inspections and repairing on the machine.
Содержание BMS-220 ADB
Страница 11: ...11...
