background image

16

HAWKER HURRICANE              Item code: BH147

.             

Instruction Manual

 

1)

 We highly recommend setting up a plane 

using the control throws listed.

 

2) 

The control throws should be measured at 

the widest point of each control surface.

 

3) 

Check to be sure the control surfaces move 

in the correct directions.

Control throw Ailerons:

 

 

Low: 10mm up / down.

 

High: 15mm up / down.

Control throw Flaps:

 

 

Mid: 16mm down.

Control throw Elevators:

 

 

Low: 8mm up / down. 

 

High: 12mm up / down.

Control throw Rudder: 

 

Low: 20mm left / right. 

 

High: 25mm left / right.

CONTROL THROWS

 

1)

  Completely  charge  your  transmitter  and 

receiver batteries  before your first day of flying.

 

2) 

 Check every bolt and every glue joint in  

your plane to ensure that everything is tight and 
well bonded.

 

3) 

 Double check the balance of the airplane.

 

4)

 Check the control surface.

 

5)

 Check the receiver antenna . It should be fully 

extended and not coiled up inside the fuselage.

 

6)

 Properly balance the propeller.

We wish you many safe and enjoyable 

flights with your 

HAWKER HURRICANE.

PRE-FLIGHT CHECK

10mm

10mm

16mm

8mm

8mm

20mm
20mm

Flap control

Aileron control

Elevator control

Rudder control

Содержание BH147


















Отзывы: