tools operation. If damaged, have the power tool
repaired before use.
Many accidents are caused
by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained
cutting tools with sharp cutting edges are less likely
to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This
will ensure that the safety of the power tool is maintained.
6. Electrical Safety
Warning!
If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified
person in order to avoid damage or injury. If the power
cord is replaced by an equally qualified person, but
not authorized by Black &
Decker, the warranty will
not be valid.
7. Labels on Tool
The label on your tool may include the following symbols:
►
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord.
Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
►
Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
►
Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
►
To reduce the risk of injury,
user must read and
understand instruction manual before operating planer.
► Be sure the voltage agrees with specific data on the
nameplate.
► Make certain that the switch is in the
OFF
position before
connecting plug to a power source.
► Be sure to switch
OFF
immediately if tool is jammed in work.
► Be sure tool is set for correct depth before turning switch
to
ON.
► Be sure to use specified replacement parts only.
► Be sure tool is disconnected from power source when
cleaning or making adjustments to the tool.
► Be sure to maintain tool with care. Follow instructions for
lubricating and changing accessories.
► Stay alert – never operate the unit when tired or under the
influence of drugs, alcohol, or medication.
► Be sure to store tool in a clean dry place after
disconnecting from power source.
► Do not use in dangerous environments. Do not use near
flammable substances, in damp or wet locations,
or expose to rain.
► Be sure that the blades are mounted as described in
the instruction manual and check that all screws are firmly
tightened before connecting unit to power source.
► Keep air vents unobstructed for proper motor cooling.
►
DO NOT
lay tool down on shoe when the blades are
exposed. This can chip the blades.
► Keep side discharge chute unobstructed at all times.
► Never reach under the tool for any reason unless it is
turned off and unplugged.
Blades are exposed and
extremely sharp.
► Use this tool for working with wood and wood products only.
► Never operate without securely holding the front handle.
► Always operate planer with two hands.
► Planer blades are extremely sharp. Handle with great care.
► Clean out your tool often, especially after heavy use.
Warning!
Always use safety glasses. Everyday
eyeglasses are
NOT
safety glasses. Also use face or dust
mask.
Always wear certified safety equipment:
► ANSI Z87.1 eye protection (CAN/CPA Z94.3),
► ANSI S12.6 (S3.19) hearing protection,
► NOSH/OSHA respiratory protection.
Warning!
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to the state of California to cause cancer,
birth defects or other reproductive harm.
Some examples of these chemicals are:
► lead from lead-based paints,
► crystalline silica from bricks and cement and other
masonry products, and
ADDITIONAL SAFETy RULES
FOR HAND PLANNER
Read Instructions
Manual
Use
Eye
Protection
Use
Ear
Protection
V ........ Volts
A ........ Amperes
Hz .......Hertz
W ........Watts
min ..... minutes
.... Alternating
Current
.... Direct
Current
n
0
....... No-Load
Speed
.... Class II
Construction
.... Earthing
Terminal
.... Safety
Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
18 • ENGLISH
