manualshive.com logo in svg

Biotech Top Light Zero 18, Руководство пользователя

Поделиться
Скачать
Biotech Top Light Zero 18 Скачать руководство пользователя страница 36

36

B. Frost protection

Each component has its own frost protection process.
Buffer

If the buffer is off (power manager Off or mode Off), charging is started when indicated by the 
activation/deactivation temperature, regardless of the time settings.

Hot water

If the hot water tank is off (power manager Off or mode Off), charging is started when indicated by 
the activation/deactivation temperature, regardless of the time settings.

Heating 
circuit

If the heating circuit is off (power manager Off or mode Off), the heating circuit is run in reduced 
mode.

C. Seizing protection

If the pumps have not been run for a week, they are turned on for a minute. The mixer drives are opened and closed 
again for double the mixer run time (before the heating circuit pump is turned on).

07

Regular maintenance

In order to keep the system in good working efficiency and order, the boiler must be cleaned at regular intervals.

7.1 Empty out the ash compartment / clean the combustion chamber

Depending on the quality of the pellets, the ash compartment and combustion chamber must be emptied out and 
cleaned every 6 – 18 weeks. These are located behind the left housing hatch and are closed with the ash compartment /  
combustion chamber doors (secured with a spoked handle / wingnut respectively).

• Procedure 

CAUTION: Never attempt to handle hot ash or glowing embers!

Press the ON/OFF switch to turn the 

 heating off.

CAUTION:  

We recommend leaving the system 2 - 3 hours to cool down after switching it off

Please note that damage caused by failure to observe the maintenance 

instructions is not covered by the warranty/guarantee.

Содержание Top Light Zero 18









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды