manualshive.com logo in svg

Biotech Top Light Zero 18, Руководство пользователя

Поделиться
Скачать
Biotech Top Light Zero 18 Скачать руководство пользователя страница 18

18

Flow temperature characteristic curve

The flow characteristic determines the relationship between the flow temperature and the outdoor temperature.

1 Up arrow

Increases the flow target temperature, left -20° C, right +20° C outdoor 
temperature

2 red value (left)

Day flow target temperature at -20° C outdoor temperature

3 blue value (left)

Lowering flow target temperature at -20° C outdoor temperature
The difference between the day and lowering flow target temperatures is given by the 
difference between the day and lowering temperatures (see basic settings, page 17) 
multiplied by the "room influence"

4 Down arrow

Decreases the flow target temperature

5 dashed line (top)

Maximum flow temperature

6 red value (right)

Day flow target temperature at +20° C outdoor temperature

7 blue value (right)

Lowering flow target temperature at +20° C outdoor temperature

8 dashed line (bottom)

Minimum flow temperature


Содержание Top Light Zero 18









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды