Biontech BTM-105DN, Руководство по эксплуатации

Страница: 16 / 40

16
5. Installation and Connection
of Alkaline Electrolysis Ionized
Water System Main Unit
* Close the valve located next to the water meter. Leave a water tap open until no water
flows out of the tap.
Install the Electrolysis Ionized Water System main unit in the sink cabinet, and connect the
main unit to the intermediary valve and the dual spouted faucets.
Connect the (1/4” size) water supply hose to the main unit.
(Using the white soft hose will result in leakage. Make sure to use the blue hose.)
Connect the water supply hose connected to the main unit to the nipple of the
intermediary valve.
Connect the control panel cord to the main unit.
■ In the case of piping extension necessity:
- Install the outlet hoses from the main unit (the alkaline ionized water hose and the
acidic ionized water hose) so that they are not bent or twisted.
- If the product is located far from the water valve, purchase an addition length of
hose to extend the water supply hose.
(1) Connect the connector of the control panel cord securely.
(2) Arrange the connector cord so that it can be pulled out through the cover groove.
- The cord outlet is located on the part of the cover.
- Do not apply excessive force to the connector.
(3) Close the connector cover.
* Make sure to close the connector cover.
(Insects may get inside the main unit through the connector cover.)
1. Make sure to check any leakage, after installation.
2. When connect water suppply hose, if the end of the hose isn’t straight, it can be caused leakage.
3. Make sure the water supply hose to connect by the one touch fitting.
4. Make sure insert the water supply elbow to until edge of part.
* Secure a space for easy filter replacement.
* Make sure the alkaline ionized water hose, the
acidic ionized water hose and the supply water
hose are not bent.
(Otherwise, leakage may occur or improper pH levels.)
* Caution) Please ensure that the alkaline ionized water
hose and the acidic ionized water hose are not bent
into a U shape.
Cut the accessory hose (900mm) to a suitable length.
(If the length of the hose is not suitable, improper pH levels will result.)
* After completion of piping, fix each hose with the bending hose-fixing clip.
* After completion of piping, do not incline the main unit.
(Dust Filter)
Reduce Valve
NIPPLE
Safety pin
Safety pin
Safety pin
Adaptor(Small)
Water Flow
control screw
Control using by
driver
Increase Decrease
Hose
1) 1/4 Hose (Tubes:PE)
2) Gripper cap
3) Gripper Ring (STS)
4) Collets
5) O-ring (NBR)
6) Body (POM)
- Cut 1/4 hose vertically before
inserting.
- 1/4 hose should be clean &
without any flaw.
- During insertion, completely put to
push till stop side of 1/4 hose
deeply although there feels
suspended in the middle.
- Slightly pull 1/4 hose to be sure to
set to hold correctly.
- Collets Stainless teeth prevent
from breakaway & O-ring prevent
from leak.
- Inserting safety pin between
collets surrounding 1/4 & body
not to breakaway.
- Put to push collets surrounding
1/4 toward body not to have any
interval between them and pull
1/4 hose to disassemble Fitting.
3 . c i P 2 . c i P 1 . c i P
6 . c i P 5 . c i P 4 . c i P
Hose
Hose
( )
(O)
How to assemble & disassemble one touch fitting
- Must use to cut the edge of
damaged hose for recombination
after desorption.