MOD. G864
13
5. FOOTREST ASSEMBLY.-
Pick up the left footrest (11) marked with the letter (L),
and insert the axle in the foot strap (9) Fig.7.
Next, get the fottrest support plate (19) and screw it
through the center hole with the screws (35), the spring
washer (66) and the flat washer (58), next srew the
holes at the endges of the plate (19) with the screws
(31) the spring washers (66) and the flat washers (55).
Perform the same assemble with the right footrest (12)
marked with the letter (R) in the foot strap (10) Fig.7.
ATTENTION: It is advisable to retighten these
screws after one month of using the machine.
6. FITTING THE FOCUS BARS.-
Insert the left focus bar (7) (marked with the letter “L”)
onto the focus bar spindle Fig.8, fit the washered bolts
(35) and spring washer (66) and the flat washers (57)
and with the help of the box spanners tighten securely.
Take the right focus bar (8), (marked with the letter “R”)
and go through the same assembly procedure as with
the left.
7. FITTING THE FOOT STRAP.-
Fit the foot strap (11) and position it with the lower
focus bar (7) as shown in Fig.8, lining up the holes.
Next, insert the bolt (37) and tighten using nut (74).
Fit the foot strap (12) and position it with the lower
focus bar (8) as shown in Fig.8, lining up the holes.
Next, insert the bolt (37) and tighten using nut (74).
Next place the lower rod closure caps (110 and 111),
fix with screws (45 and 46) Fig.8.
If you feel the foot strap has looseness, follow these
steps:
- Remove the bolt (35).
- Add one or more 0.15 mm washers as shown in
Fig.8.
- Tighten again bolt (35).
8. FITTING THE UPPER FOCUS BARS.-
Once you have assembled the top focus bars, take the
lower focus bar (5) (marked with the letter “L”) and insert it
onto the boss for the top bar (7), Fig.9, lining up the holes
for the screws.
Refit the screws (33), the washers (55) and the spring
washers (66), Fig.9, and tighten securely.
Go through the same procedure for the lower right
focus bar (6) (marked with the letter “R”).
9. FITTING THE FOCUS BAR SPINDLE
COVERS.-
Take the front (108) and rear (109) covers and
position them on the main post (8), Fig.9. Now use
the screws (45) to attach them to the post.
Take the front (108) and rear (109) covers and
position them on the main post (7), Fig.9. Now use
the screws (45) to attach them to the post.
10. FITTING THE HANDLEBAR.-
Bring the handlebar (122) up to the handlebar stem (2),
Fig.10, insert the hand-grip cable (131) in through the
slot as shown in Fig.10, and pull it out through the top
of the handlebar stem.
Refit the screws (32), the washers (54) and the spring
washers (66), Fig.10, and tighten securely, then fit the
bracket cover (105).
11. BOTTLE HOLDER ASSEMBLY.-
Place the bottle holder (106) in the tube (2), next place
the botel holder support (107) and screw with screws
(49) Fig.10.
12.- FITTING THE MONITOR.-
Next, connect terminals (129) (131), sticking out of the
handlebar (2), and terminal (B) (C), sticking out of the
monitor (124), Fig.11.
Place the monitor (124) on top of the plate on the main
post (2), as shown in Fig.11, making sure not to pinch
the wires.
Use screws (45) to hold the monitor in place, Fig.11.
LEVELLING.-
Once the unit has been placed into its final position,
make sure that it sits flat on the floor and that it is level.
This can be achieved by screwing the adjustable feet
(84) up or down, as shown in Fig.12.
MOVEMENT & STORAGE.-
The unit
is equipped with wheels (92), as shown in
Fig.13, which make it easier to move. The two wheels
at the front of the unit make it easier to place the unit in
to any chosen position by lifting the rear slightly
Store your unit in a dry place, preferably not subject to
changes in temperature.
MAINS CONNECTION.-
(Optional).
Insert the jack (m) for the transformer into the
connection hole on the main body (k) (bottom, rear of
the machine) and then plug the transformer (142) into a
220 V mains supply, Fig.14.
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE.
Do not hesitate to get touch with us if you have any
queries, by calling:
+44 0844 335 3988 [email protected]
Содержание G864
