Beta Marine BetaGen 10 Скачать руководство пользователя страница 81

Страница: 81 / 116

Problem: Vibrations

Possible Cause

Solution

Flexible mounts not adjusted correctly to take even weight: Check relative compression of each mount.

Flexible mount rubber perished:

Replace, diesel or engine oil will eventually

perish rubbers.

Loose securing nut on flexible mount:

Check alignment and then tighten the nuts.

Weak engine support/bearers:

Check for cracked or broken feet.

Problem: Knocking noise

Possible Cause

Solution

Flexible mount stud touching engine bed:

Adjust stud to clear.

Drive plate broken:

Replace/repair.

Engine touching engine bed:

Re-align engine/modify bed.

Injectors blocked through excess carbon

Remove and check injector nozzles, replace if required.

caused by water in the fuel:

Problem: Battery quickly discharges

Possible Cause

Solution

High load and insufficient running:

Reduce load or increase charging time. Large domestic

battery banks subject to high electrical loads will take a

considerable time to recharge from a single alternator.

Low electrolyte level:

Top up.

Fan belt slipping - black dust in engine compartment,

Adjust tension/replace belt with a high temperature

engine compartment temperature too high:

type and/or improve engine compartment ventilation.

Alternator defective:

Check with dealer or service agent.

Battery defective:

Replace.

Poor wiring connection:

Check wiring system.

Содержание BetaGen 10





















































































































Результаты поиска

Содержание BetaGen 10

Отзывы:

Бренды по названию

Популярные бренды

Beta Marine BetaGen 10, Руководство по установке

Результаты поиска

Содержание BetaGen 10

Отзывы:

Бренды по названию

Популярные бренды