manualshive.com logo in svg

Beta Marine BetaGen 10, Руководство по установке

Поделиться
Скачать
Beta Marine BetaGen 10 Скачать руководство пользователя страница 52

50

ENGINE LUBRICANT

{

 
Engine oil:

 Engine oil quality should have the minimum 

properties of the American Petroleum Institute ‘API’ 
classification 

CF

 with multi-grade SAE ratings as listed in 

the following table. 

NB:

 An acceptable alternative is a mineral based, semi-

synthetic lubricating oil with a content mix no greater 
than 30% being synthetic based.

The adjacent table gives grades of oil viscosity required for 
various ambient temperature ranges.

 Ambient  Temp. 

Multi-Grade

 -30°C to 0°C 

SAE 10W/30

-15°C to +15°C 

SAE 15W/40

0°C to +30°C 

SAE 15W/40

25°C and above 

SAE 15W/40

 

IMPORTANT! 

•  Do not mix two different types of oil or SAE 

rating.

•  Do not use lubricant additives and/or fully 

synthetic lubricating oil.

 

WARNING!

New engines are supplied with the engine lube 
oil drained off.

AC ELECTRICAL INSTALLATION

{

 

WARNING! - ELECTRICITY IS DANGEROUS AND CAN CAUSE DEATH IF THE 

GENERATING SET IS NOT CORRECTLY INSTALLED, MAINTAINED AND USED

 

WARNING!

Refer to the independent AC alternator 
manufacturer’s operator manual originally 
supplied with the generating set. If required, 
replacement AC alternator PDF files can be be 
downloaded from our website:

www.betamarine.co.uk

 IMPORTANT!

The decision to connect to the AC electrical 
output terminals of the generating set is the 
responsibility of a qualified/certified electrician 
who is also responsible for ensuring the safety, 
integrity & quality of the electrical circuit being 
connecting to.

Содержание BetaGen 10





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды