Beta Marine BetaGen 10 Скачать руководство пользователя страница 79

Страница: 79 / 116

Problem: Black exhaust gas

Possible Cause

Solution

Blocked air filter element:

Inspect and replace.

Problem: High oil consumption

Possible Cause

Solution

Oil leaks:

Check for leaks.

Piston rings worn:

Overhaul required.

Valve stem and guide worn:

Overhaul required.

Piston rings gap facing the same direction:

Shift ring gap position. Dealer or service agent to check.

Problem: Water in lubricating oil - general

Possible Cause

Solution

Core plug pushed out due to frozen block:

Dealer or service agent to check and replace.

Water pump seal damaged:

Dealer or service agent to check and replace.

Problem: Water in lubricating oil - heat exchanger cooled

Possible Cause

Solution

Oil goes “milky” due to seawater entering

Check installation - has an anti-syphon valve been fitted?

exhaust manifold:

Change engine oil and run engine for 10 minutes each

time to eliminate any water. Get fuel injection pump and

compression checked by dealer or service agent.

Problem: Water in lubricating oil - keel & radiator cooled

Possible Cause

Solution

Oil goes “milky” due to water entering

Check installation - has the dry exhaust system been

exhaust manifold and then into the sump:

fitted correctly, ensuring rain water cannot enter the

exhaust port and run back? (please refer to ‘Dry Exhaust

System on page 40). Change engine oil and run engine

for 10 minutes each time to eliminate any water. Get

injection pump checked by dealer or service agent.

Содержание BetaGen 10





















































































































Результаты поиска

Содержание BetaGen 10

Отзывы:

Бренды по названию

Популярные бренды

Beta Marine BetaGen 10, Руководство по установке

Результаты поиска

Содержание BetaGen 10

Отзывы:

Бренды по названию

Популярные бренды