Beta Marine BetaGen 10 Скачать руководство пользователя страница 78

Страница: 78 / 116

Problem: Low power output

Possible Cause

Solution

Blocked fuel filter:

Replace.

Blocked air filter:

Replace.

Air in fuel system:

Check system and bleed.

Governor spring incorrectly mounted:

Dealer to adjust.

The electrical load is too large on start up:

Disconnect or reduce the load.

Problem: Erratic running/hunting

Possible Cause

Solution

Air in fuel supply:

Check supply system for leaks and fix.

Fuel lift pump faulty:

Replace.

Clogged fuel filter:

Replace.

Fuel return not fed back to the fuel tank, or blocked pipe: Re-route pipe or clean.

Air filter blocked:

Replace.

Worn or blocked injector:

Service injectors.

Engine rpm in gear is too low, this must be 850 min:

Increase engine tick over speed.

Faulty stop solenoid:

Disconnect wiring to solenoid. If running improves

check for a wiring fault.

Broken fuel injection pump spring:

Replace, this is usually caused by water in the engine

oil/fuel.

Fuel suction head is too great:

Fit electric fuel lift pump.

Problem: Hunting

Possible Cause

Solution

Fuel supply problem:

Change fuel filter and check fuel supply.

Problem: White or blue exhaust gas

Possible Cause

Solution

Engine oil level too high:

Reduce the level.

Blocked injector:

Service injectors.

Piston ring and bore worn or con rod bent due to water

Get the compression checked by your dealer or

ingression, giving a low compression:

service agent. They will advise action to be taken.

Check that the breather pipe is clear and not obstructed:

Remove and clean out.

Содержание BetaGen 10





















































































































Результаты поиска

Содержание BetaGen 10

Отзывы:

Бренды по названию

Популярные бренды

Beta Marine BetaGen 10, Руководство по установке

Результаты поиска

Содержание BetaGen 10

Отзывы:

Бренды по названию

Популярные бренды