manualshive.com logo in svg

Beta Marine BetaGen 10, Руководство по установке

Поделиться
Скачать
Beta Marine BetaGen 10 Скачать руководство пользователя страница 44

42

FUEL SYSTEM

{

•   If a fuel supply shutoff valve is fitted do not use a 

taper tap, only use a ball valve tap. The ball valve type 
are more reliable and less likely to let air into the fuel 
system.

•   Be sure to use a strainer when filling the fuel tank. 

Dirt or sand in the fuel may cause trouble in the fuel 
injection pump.

•   Always use diesel fuel. 

Do not use paraffin/

kerosene

, as this has a low cetane rating and 

adversely affects the engine.

•   Biodiesel fuel can be added to the normal diesel fuel 

up to a maximum limit of 7% without affecting the 
warranty.

•  Most diesel fuels now contain up to a maximum limit  

of 7% Biodiesel and this does not affect the engine 
warranty. The recent changes to fuel specifications 
allow the addition of FAME (fatty acid methyl ester) 
Biodiesel EN14214:2009, to diesel fuel, but please be 
aware that Biodiesel does allow bacteria to grow more 
easily in the fuel and this can clog your fuel tank, pipes 
and filters. If you experience an outbreak of bacterial 
growth you can either empty and clean out your fuel 
pipes and tank, or use biocide additives and filtering.

•  Low sulphur diesel fuel - regulations changed recently 

reducing the sulphur content by 99%, in many 
countries. The European standard is EN590:2009, and 
in the USA ASTM D975-09. The engine is designed to 
run on low sulphur fuel, and this is now preferred.

•  If you use a higher percentage of Biodiesel fuel you 

must fit an electric lift pump into the fuel supply line, 
and the fuel filter and oil filter must both be changed 
together when the oil filter is normally replaced. 

•   Be careful not to let the fuel tank become empty, or 

air can enter the fuel system, necessitating bleeding 
before next engine start.

•   The engine mechanical fuel lift pump will only lift fuel 

through 0.25m. If this is insufficient then an electric 
fuel lift pump must be fitted.

 

IMPORTANT!

Beta Marine warranty will not cover fuel 
equipment when more than 7% Biodiesel is 
used.

 

WARNING!

Always fit a fuel/water separator in the fuel 
supply system. Water in the fuel can seriously 
damage the injection system

.

26

Fuel/Water Separator

Содержание BetaGen 10





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды