background image

PowerBoard

®

 NX – Installation Instructions

Rev. G 0713

75638 / 75643 pg. 2

Motor Linkage,

Right  (Shown)  -      

Part Number 
475.54, Qty - 1

Left - Part 

Number 475.55, 
Qty - 1

7" Cable Ties, Part Number 460.99, Qty - 25

11" Cable Ties, Part Number 470.02, Qty - 2

Running Board Assembly, Qty - 2
  72" - Part Number 473.14 
  79" - Part Number 460.87

Left End Cap, 
Part Number 
460.83, Qty - 1

Right End Cap, 
Part Number 
460.82, Qty - 1

T-Nut Insert, Part 
Number 460.84, 
Qty - 2

M6 Nut Plate, 
Part Number 
460.86, Qty - 2

M6-1.0 x 10mm Socket 
Cap Screw, Part Number 
460.85, Qty - 2

Light, Part Number 
470.15, Qty - 4

M8-1.25 x 30 Hex 
Bolt, Part Number 
473.18, Qty - 12

Reinforcement Bracket, 
Part Number 494.62, 
Qty - 4

M6-1.0 x 20 Socket Cap Screw, 
Part Number 470.00, Qty - 8

8mm Washer, 
Part Number 
470.07, Qty - 1

8 mm Washer, 
Part Number 
470.05, Qty - 8

M8-1.25 x 25 
Hex Bolt, Part 
Number 460.46, 
Qty - 1

M8-1.25 Nylock 
Nut, Part Number 
470.06, Qty - 1

Brake Cable 
Bracket, Part 
Number 473.78, 
Qty - 1

Parts List and Hardware Identifi cation 

75643 Quad Cab Only 

M8-1.25 Rivet Nut, Part 
Number 473.75, Qty - 8

Rivet Nut Tool, Part 
Number 473.76, Qty - 1

M6-1.0 x 35 Socket Cap 
Screw, Part Number 
460.95, Qty - 6

M6-1.0 x 30 Hex Bolt, 
Part Number 474.36, 
Qty - 4

8 mm Fender 
Washer, Part 
Number 470.07, 
Qty - 4

M8-1.25 x 15 Flange 
Bolt, Part Number 
473.81, Qty - 2

Front Support Bracket - Rt, 
Part Number 481.86, Qty - 1

Bracket Insert, 
Part Number 
473.35, Qty - 4

Roll Pin, Part 
Number 475.12, 
Qty - 8

Idler Linkage,

Right  (Shown)  -      

Part Number 
475.52, Qty - 1

Left - Part 

Number 475.53, 
Qty - 1

Rear Support 
Bracket, Part 
Number 474.35, 
Qty - 2
Not used on Mega 
Cab

Front Support Bracket - Lt, 
Part Number 481.87, Qty - 1

M6-1.0 x 15 Socket Cap Screw, 
Part Number 481.93, Qty - 2

Mounting Insert, Part 
Number 474.34, 
Qty - 4

Blind Rivet, Part Number 
474.80, Qty - 4

Wiring Harness, Part 
Number 495.56, Qty - 1

M6 Flat Washer, 
Part Number 
481.96, Qty - 8

Blue Controller, Part 
Number 496.11, Qty - 1

Motor (for use with Blue 
Controller), Part Number 
496.12, Qty - 2

Magnet, Part 
Number 491.97, 
Qty - 5

Magnet Holder, Part 
Number 491.98, Qty - 5

Sensor - Passenger 
Side Front, Part Number 
492.00, Qty - 1

Wireless Component Kit

Sensor - Passenger 
Side Rear, Part Number 
492.02, Qty - 1

Sensor - Driver Side 
Front, Part Number 
492.01, Qty - 1

Sensor - Driver Side 
Rear, Part Number 
492.03 , Qty - 1

Receiver, Part Number 
491.99, Qty - 1

17" Nylon Zip Tie, Part 
Number 492.06, Qty - 2

Содержание powerboard nx















Отзывы: