background image

PowerBoard

®

 NX  – Installation Instructions

Rev. G 0713

75638 / 75643 pg. 9

Install Motor

Mount the Steps to the linkages. Slide the mounting T-Nut 
into position. Install M6-1.0 x   Socket Head Bolts to secure 
the boards. Use a 5mm Allen Wrench to tighten the bolts.

Make sure the board moves up and down freely by hand. 
If it binds, loosen the linkage to body attachment bolts and 
adjust the linkage position until the boards move freely. 

Do 

not tighten the bolts at this time.

M6-1.0 x 20mm 
Socket Head Bolts

Arm

PowerBoard

Install Running Boards

M6-1.0 x 20mm 
Socket Head Bolts

M6-1.0 x 20mm 
Socket Head Bolts

Tightening the 
fasteners before 

cycling the step several times 
may create a bind, causing a 
squeaking sound and preventing 
the boards from retracting 
completely and evenly.

Open the back door on the driver’s 
side and clean the area where the 
magnet and sensor will be installed 
with a 50/50 solution of water and 
alcohol. Stick a magnet to the back 
side of the front door as shown. 
Hold the Drivers Front Sensor 
against the door pillar and position 
the magnet so it is directly in front 
of the sensor.

Slide Motor assembly onto drive shaft and mounting 
bosses of Motor Linkage assembly. Use three (3) 
M6-1.0 x 35mm Socket Cap Screws and M6 Flat 
Washers to secure Motor. Plug female connector into 
Motor. 

M6-1.0 x 35mm Socket Cap 
Screws and M6 Flat Washers

Driver’s Side 
Rear Door

Top Hinge

Magnet

Install Magnet 

Torque

5-7 ft. lbs. 

(6.78-9.49 Nm / 
60-84 in. lbs.)

Do not exceed 7 
ft. lbs. of torque

Install Driver’s Side 
Front Sensor 

Peel the liner off of the Drivers Side 
Front Sensor. Position it on the door 
pillar so it is about 1/6" away from the 
magnet. Press fi rmly on the Sensor to 
stick it to the pillar.

Driver’s Side 
Rear Door

Driver’s Front 
Sensor

Sensor sits 
on top of 
hinge

Top Hinge

Magnet

Содержание powerboard nx















Отзывы: