background image

PowerBoard

®

 NX – Installation Instructions

Rev. G 0713

75638 / 75643 pg. 14

LIMITED WARRANTY

We warrant our product to be free from defects in material and workmanship, for the terms specifi ed below, provided there has been normal 
use and proper maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair or 
replacement of any item or items found by the factory to be defective within the time period specifi ed.  If you have a warranty claim, fi rst you must 
call our factory at the number below for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty 
work. Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our 
products caused by accidents, fi re, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is 
not covered under this warranty.  

THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL PowerBoards

®

  MANUFACTURED BY OUR COMPANY: THREE YEARS / 36,000 

MILES FROM DATE OF PURCHASE.

ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED 
IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE 
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, 
so the above limitations or exclusions may not apply to you. This warranty gives you specifi c legal rights, and you may also have other rights which 
vary from state to state.

For further information or request for warranty work, please contact:
Bestop Inc. Customer Service
Toll-Free: (800)845-3567
Main: (303)465-1755
E-mail: [email protected]
Website: www.Bestop.com

Содержание powerboard nx















Отзывы: