background image

PowerBoard

®

 NX – Installation Instructions

Rev. G 0713

75638 / 75643 pg. 8

Route the long leg of the Wire Harness across the 
engine compartment to the passenger side wheel 
well. Route the short leg to the driver’s side. Secure 
them with 7" Cable Ties.

Route Wiring Harness

Wire 
Harness

On the driver’s side route the Wire Harness down 
along the underside of the fl oor and the frame. 
Secure it with 7" Cable Ties.

Route Wiring Harness – 
Driver’s Side

Wire 
Harness

Continue to route the Wire Harness along the inside 
and top of the driver’s side frame. Secure it with 7" 
Cable Ties.

Route Wiring Harness – 
Driver’s Side

Wire 
Harness

7" Cable 
Tie

7" Cable 
Tie

Route the Wire Harness down to the wheel well on the Passenger side and along 
the top of the frame rail. Secure it with 7" Cable Ties.

You may have to combine Cable Ties to create longer ties.

Route Wiring Harness – Passenger’s Side

7" Cable 
Ties

Wire 
Harness

Install Receiver

Route the small diameter wire harness along the side of the frame. Find a 
location that is protected but is not surrounded by dense metal. Plug in the 
Receiver and insert 17" Nylon Zip Ties through the loops on the Receiver. 
Mount the Receiver with the stand off ribs against the vehicle.

Due to vehicle variations, installation may differ from 
that shown.

Receiver

Small Diameter 
Wire Harness

Frame

17" Nylon 
Zip Ties

Do Not install on or near 
hot surfaces.

Содержание powerboard nx















Отзывы: