Beretta CIAO 20 S C.S.I. Скачать руководство пользователя страница 9

Страница: 9 / 84

CIAO S C.S.I. - CIAO S R.S.I.

By activating the function the burner is ignited through simula-

tion of heat request in heating.

To perform calibration operations, proceed as follow:
- switch off the boiler
- remove the shell and access the card
- insert the jumper JP1 (

g. 16) to enable the knobs placed on the

control panel to the minimum and maximum heating adjustment

functions.

- make sure that the mode selector is in winter position (see section

4.2).

- power the boiler

Electric card in voltage (230 Volt)

- turn the heating water temperature adjustment knob

(

g. 17) until

it reaches the minimum heating value as indicated in the multigas

table

- insert the jumper JP2 (

g. 16)

- turn the domestic hot water temperature adjustment knob

(

17) until it reaches the maximum heating value as indicated in the

multigas table

- remove the jumper JP2 to store the maximum heating value
-

remove the jumper JP1 to store the heating minimum value

and to get out the calibration procedure

- reconnect the compensation inlet to the air distribution box
Disconnect the pressure gauge and retighten the pressure test point

screw.

nish the calibration function without storing the set values,

proceed as follows:

a) set the mode selector to position (OFF)

b) remove power supply voltage

c) remove JP1/JP2

The calibration function is automatically

nished, without storing

minimum and maximum values, after 15 minutes of its activa-

tion.

The function is automatically

nished also in case of de

nitive

stop or lockout.

Also in this case, function conclusion DOES NOT provide values

storing.

Note

To calibrate only maximum heating, it is possible to remove the

jumper JP2 (to store the maximum) and then get out from the func-

tion, without storing the minimum, setting the mode selector to

(OFF) or removing the voltage from the boiler.

After each intervention on the adjustment element of the gas

valve, seal it with sealing varnish.

When adjustment is complete:

- restore set temperature with the ambient thermostat to the desired

temperature

- set the heating water temperature selector to the desired position

- close the instrument panel

- pull the shell back in place.

4.6 Gas conversion operations

Conversion from a family gas to other family gas can be performed

easily also when the boiler is installed.
The boiler is designed to operate with methane gas (G20) according

to the product label.
It is possible to convert the boilers from one gas type to another by

using the appropriate kit supplied upon request:
-  Methane conversion kit
-  LPG conversion kit
For disassembly refer to instructions below:
-  remove power supply from the boiler and close the gas tap
-  remove in sequence: shell, air distribution box cover and combus-

tion chamber cover (

g. 19)

- disconnect the spark plug cable connection
- slide off the lower cable grommet from the seat of the air distribution

box

- remove the burner

xing screws and remove the latter with the

spark plug attached and corresponding cables

- using a socket or fork spanner, remove the nozzles and the wash-

ers and replace them with the ones in the kit.

Use and assemble the washers contained in the kit also

in case of manifolds without washers.

- reinsert the burner in the combustion chamber and tighten the

screws

xing it to the gas manifold

- place the cable grommet with the spark plug cable in its seat in

the air distribution box

- restore connection of the spark plug cable

- re

t the combustion chamber cover and the cover of the air distribu-

tion box

- overturn the control instrument panel towards the boiler front part

- open the card cover

- on the control card (

g. 16):

- if the conversion is from methane gas to LPG, insert the jumper

in position JP3

- if the conversion is from LPG to methane gas, remove the jumper

from position JP3

- reposition the components previously removed

- restore voltage to the boiler and reopen the gas tap (with boiler

in operation, check correct seal of the gas feeding circuit connec-

tions).

Conversion must be carried out by quali

ed personnel.

After conversion, adjust the boiler again following the

indications in speci

c section and apply the new identi

cation label contained in the kit.

5 MAINTENANCE

o ensure product characteristics and ef

ciency remain intact and

to comply with prescriptions of current regulations, it is necessary

to render the appliance to systematic checks at regular intervals.

Control frequency depends on the installation and use conditions,

but it is therefore necessary an annual check-up by the authorised

personnel from the Technical Assistance Service.

Turn off the appliance to carry out the maintenance of the structure

near the

ue exhaust connections or devices, and their accessories.

Once the interventions are

nished a quali

ed technician must check

that the pipes and the devices work correctly.

IMPORTANT:

before carrying out any cleaning or maintenance

operation of the appliance, use the appliance and system switch

to interrupt power supply and close the gas supply turning the tap

placed on the boiler.

Do not clean the appliance or its parts with in

ammable substances

(e.g. petrol, alcohol, etc.).

Do not clean panels, painted parts and plastic parts with paint thinner.

Panel cleaning must be carried out only with soapy water.

5.1 Check the combustion parameters
Ciao S C.S.I.:

To carry out the combustion analysis, proceed as follows:

- open the hot water tap to its maximum output

- set the mode selector to summer

and the domestic hot water

temperature selector to the maximum value (

g. 8a).

- remove the screw of the combustion analysis inlet cover (

g. 18)

and insert the probes

- power the boiler

Ciao S R.S.I.:

- switch off the boiler

- set the function selector to winter mode

- remove the housing and access the card

- insert the jumpers JP1 and JP2

- use a screwdriver to prise open the plug on the control panel

- bring the trimmer P2 to the maximum value, using a screwdriver

(turn clockwise)

- remove the screw of the combustion analysis inlet cover (

g. 18)

and insert the probes

- power the boiler

The appliance works at maximum output and it is possible to check

combustion.

After analysis is complete:

- close the hot water tap

- remove the probe from the analyser and close the combustion

analysis inlet fastening carefully the screw previously removed.

Содержание CIAO 20 S C.S.I.





















































































Результаты поиска

Содержание CIAO 20 S C.S.I.

Отзывы:

Бренды по названию

Популярные бренды

Beretta CIAO 20 S C.S.I., Инструкция по установке и эксплуатации

Результаты поиска

Содержание CIAO 20 S C.S.I.

Отзывы:

Бренды по названию

Популярные бренды