Bercomac 700370-3 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 36

Bercomac 700370-3 Скачать руководство пользователя страница 7

5

ASSEMBLY

Install the mounting pins

IF YOUR TRACTOR IS NOT EQUIPPED WITH
MOUNTING PINS:

Remove the bolt that holds the left hand side mower lift
arm (item 1). Reinstall the lift arm by inserting (as
shown) the mounting pin (item 2), original sleeve (item
4) and flat washer (item 3) from the tractor.

Secure with the original nut inside the tractor frame.

Do the same operation on the right side.

Tighten firmly.

View once unpacked

STEP 1
SUBFRAME PREPARATION

MODÈLS: LX 255, 266, 277, 277AWS, 279, 288 &
GT 225, 235, 245 & G-100

IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE (SEE TABLE OF
CONTENTS) WHEN STATED: TIGHTEN FIRMLY. REFER TO PARTS BREAKDOWN SECTION FOR PARTS
IDENTIFICATION.

NOTE:

The mower deck must be removed to install the subframe.

INSTALLING THE REFLECTORS

IMPORTANT:

When operating the tractor with the

front mounted attachment, install the two red-colored
adhesive reflectors on the rear vertical surface of the
tractor’s fender.

«
...
5
6
7
8
9
...
»

Содержание 700370-3





































Отзывы:

Нет отзывов