Bercomac 700370-3 Скачать руководство пользователя страница 6

SAFETY PRECAUTIONS 

WHENEVER YOU SEE THIS SYMBOL  

 

 
 
 

IT MEANS:

 

 

WARNING! 

 

BECOME ALERT ! 

 

YOUR SAFETY IS INVOLVED!

 

 

WARNING

 

 

FOR YOUR SECURITY: 
Read the attachment owner's manual for safety 
precautions and rules.  
Follow the assembly and operation instructions.

 

 

WARNING

 

 

TO PREVENT INJURIES AND FOR MORE 
TRACTION WHEN USING AN ATTACHMENT: 
-Rear counterweight of 100 lbs. minimum is 

required to counterbalance the attachment’s 
weight. 

-Tractor manufacturer approved tire chains are 

required. 

-Do not operate on a slope greater than 10°. 
-When dismounting an attachment remove rear 

counterweights.

 

 

4. Use only attachments approved by the 

manufacturer (such as wheel chains, 
counterweights, cabs). You must use 100 lbs. of 
rear counterweight for better traction and a greater 
stability at all times when using an attachment that 
is installed on the front of a tractor. 

 

5.  Never operate an attachment without good visibility 

or light. 

 
MAINTENANCE AND STORAGE 

 
1.  Check shear bolts, mounting bolts, etc..., at frequent 

intervals for proper tightness to be sure attachment is 
in safe working condition. 

 
2.  Never store the machine with fuel in the tank inside a 

building where ignition sources are present, such as 
hot water tanks, space heaters, clothes dryers and 
the like. Allow engine to cool before storing in any 
enclosure. 

 
3.  Always refer to the owner’s manual when you store 

than attachment for an extended period. 

 
4.  Maintain or replace safety and instructions labels, as 

necessary. 

 

Содержание 700370-3





































Отзывы: