Bercomac 700370-3 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

Bercomac 700370-3 Скачать руководство пользователя страница 18

16

ASSEMBLY

Remove the belt guard from the back of snowblower.

Move the tension arm (item 8) towards the back to
facilitate the belt installation.

Install the belt on the snowblower by inserting it between
the two flat pulleys (items 1 & 2) and around the
snowblower pulley (item 4). Route the drive belt around
the V pulleys (items 5 & 6) and around the tractor drive
pulley (item 7).
Make sure the belt is not twisted between the pulleys
(items 4 & 5).

Apply tension on the belt by moving the tension arm
(item 8) towards the front and secure with a 3 mm hair
pin (item 9) in the hole (item 10).

Check the tension on the belt and adjust if necessary.

See maintenance section for belt adjustment
instructions.

CAUTION

Never use the snowblower without the belt guard.

VERIFY BELT ROUTING

-Lower the snowblower to the ground and let it run for

a few seconds under supervision.

-Disengage the snowblower and stop the engine.
-Check the belt to make sure it is well inserted in the

pulleys and that it has not flipped on its side in the
pulleys.

-Reinstall the belt guard.

Install belt

Apply tension on belt

WARNING

TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.

For more information, do not hesitate to contact
the technical support.

«
...
16
17
18
19
20
...
»

Содержание 700370-3





































Отзывы:

Нет отзывов