Bercomac 700370-3 Скачать руководство пользователя страница 4

INTRODUCTION 

TO THE PURCHASER  

 
This new attachment was carefully designed to give years of dependable service. This manual has been provided to 
assist in the safe operation and servicing of your attachment. 
 

NOTE:

 All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but 

are intended for reference only and are based on the latest product information available at the time of publication. 
 
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use. 
Carefully read, understand and follow these recommendations and insist that they be followed by those who will use 
this attachment. 
 

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL 
THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER, 
WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD. 
HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

 

 

DANGER: Signals 

an 

extreme hazard that will cause serious injury or death if recommended precautions are 

not followed. 

  
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not 

followed. 

 

CAUTION:  Signals a hazard that may cause minor or moderate injury if the recommended precautions are not 

followed. 

 

 
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on 
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement 
parts. Use only genuine parts when replacements are required. 
 
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer 
for warranty service. 
 

 

This manual should be kept for future reference. 

Please check if you have received all the parts for your kit with the list of the 

bag and the list of the box.

 

 
 

SERIAL NUMBER : 

 ____________________________  

 
 

PURCHASE DATE : 

 ____________________________  

In this manual, right and left sides are determined by sitting on the tractor seat facing forward. 

Содержание 700370-3





































Отзывы: