BendPak XP-10AC Скачать руководство пользователя

Страница: 29 / 52

OPERATION

To Raise Lift;

Load vehicle onto the lift using Vehicle Lifting Guide to

determine proper lifting points.

Set parking brake or use wheel chock to hold vehicle

in position.

Before raising vehicle, be sure all personnel are clear

of the lift and surrounding area. Pay careful attention to
overhead clearances.

Raise the lift to the desired height by pressing the push

button on the power unit.

After vehicle is raised to the desired height,

lower the

lift onto the nearest safety lock.

Do not allow cables to

become slack.

ALWAYS INSURE SAFETY LOCKS ARE

ENGAGED

before entering work area.

To Lower Lift;

Raise the lift off the safety locks by pressing the push

button on the power unit. Make sure you raise the lift by at
least two inches to allow adequate clearance for the locks
to clear.

Push the powerside safety handle and HOLD.

Push the LOWERING HANDLE on the power unit until

the lift has descended completely.

WEEKLY MAINTENANCE

Lubricate all rollers with general purpose oil or WD-40.

Check all cable connections, bolts and pins to insure

proper mounting.

Lubricate safety lock pivot points with general purpose

oil or WD-40.

MONTHLY MAINTENANCE

Check safety locks to insure they are in good

operating condition.

Check all cables for excessive signs of wear

Make a visual inspection of ALL MOVING PARTS and

check for excessive signs of wear

Replace ALL FAULTY PARTS before lift is put back

into operation.

NEVER EXCEED THE RATED CAPACITY

of lift.

DO NOT USE LIFT

if any component is found to be

defective or worn.

NEVER OPERATE LIFT

with any person or equip-

ment below.

ALWAYS STAND CLEAR

of lift when lowering or

raising.

ALWAYS INSURE SAFETY LOCKS ARE ENGAGED

before entering work area.

NEVER LEAVE LIFT IN ELEVATED CONDITION

unless all four safety locks are engaged

When lowering the lift PAY CAREFUL ATTENTION that

all personnel and objects are kept clear. ALWAYS keep

a visual line of site on the lift AT ALL TIMES. ALWAYS

make sure that all FOUR LOCKS are disengaged. If one

of the locks inadvertently locks on descent the lift and/or

vehicle may disrupt causing personal injury or death.

VISUALLY CONFIRM THAT ALL PRIMARY

SAFETY LOCKS ARE ENGAGED BEFORE

ENTERING WORK AREA.

Suspension components us on this lift are

intended to raise and lower lift only and are not

meant to be load holding devices. Remain

clear of elevated lift unless visual confirmation

is made that all primary safety locks are fully

engaged and the lift is LOWERED onto the
safety locks, Refer to installation /operation

manual for proper safety lock procedures

and /or further instruction.

Содержание XP-10AC





















































Результаты поиска

Содержание XP-10AC

Отзывы:

Похожие инструкции для XP-10AC

Бренды по названию

Популярные бренды

BendPak XP-10AC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XP-10AC

Отзывы:

Похожие инструкции для XP-10AC

Бренды по названию

Популярные бренды