BendPak XP-10AC Скачать руководство пользователя страница 3

Страница: 3 / 52

IMPORTANT NOTICE

Do not attempt to install this lift if you have never been

trained on basic automotive lift installation procedures.

Never attempt to lift components without proper lifting

tools such as forklift or cranes. Stay clear of any moving

parts that can fall and cause injury. These instructions

must be followed to insure proper installation and opera-

tion of your lift. Failure to comply with these instructions

can result in serious bodily harm and void product war-

ranty. Manufacturer will assume no liability for loss or

damage of any kind, expressed or implied resulting from

improper installation or use of this product.

PLEASE READ ENTIRE MANUAL

PRIOR TO INSTALLATION.

DEFINITIONS OF

HAZARD LEVELS

Identify the hazard levels used in this manual with the

following definitions and signal words:

DANGER !

Watch for this symbol: It Means: Immediate hazards

which will result in severe personal injury or death.

WARNING !

Watch for this symbol: It Means: Hazards or unsafe

practices which could result in severe personal

injury or death.

CAUTION !

Watch for this symbol: It Means: Hazards or unsafe

practices which may result in minor personal injury,

product or property damage.

OWNER’S RESPONSIBILITY

To maintain the lift and user safety, the responsibility of the

owner is to read and follow these instructions:

Follow all installation and operation instructions.

Make sure installation conforms to all applicable Local,

State, and Federal Codes, Rules, and Regulations;

such as State and Federal OSHA Regulations and

Electrical Codes.

Carefully check the lift for correct initial function.

Read and follow the safety instructions. Keep them

readily available for machine operators.

Make certain all operators are properly trained, know

how to safely and correctly operate the unit, and are

properly supervised.

Allow unit operation only with all parts in place and

operating safely.

Carefully inspect the unit on a regular basis and

perform all maintenance as required.

Service and maintain the unit only with authorized or

approved replacement parts.

Keep all instructions permanently with the unit and all

decals on the unit clean and visible.

BEFORE YOU BEGIN

Receiving:

The shipment should be thoroughly inspected as soon as it

is received. The signed bill of lading is acknowledgement by

the carrier of receipt in good condition of shipment covered

by your invoice. If any of the goods called for on this bill of

lading are shorted or damaged, do not accept them until the

carrier makes a notation on the freight bill of the shorted or

damaged goods. Do this for your own protection.

NOTIFY THE CARRIER AT ONCE

if any hidden loss or

damage is discovered after receipt and request the carrier

to make an inspection. If the carrier will not do so, prepare

a signed statement to the effect that you have notified the

carrier (on a specific date) and that the carrier has failed to

comply with your request.

IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE

AFTER YOU HAVE GIVEN THE CARRIER A CLEAR

RECEIPT.

File your claim with the carrier promptly. Support

your claim with copies of the bill of lading, freight bill,

invoice, and photographs, if available. Our willingness to

assist in helping you process your claim does not make

BendPak responsible for collection of claims or replace-

ment of lost or damaged materials.

Содержание XP-10AC





















































Результаты поиска

Содержание XP-10AC

Отзывы:

Похожие инструкции для XP-10AC

Бренды по названию

Популярные бренды

BendPak XP-10AC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XP-10AC

Отзывы:

Похожие инструкции для XP-10AC

Бренды по названию

Популярные бренды