BendPak XP-10AC Скачать руководство пользователя

Страница: 32 / 52

DO NOT

Leave the controls while the lift is still in motion.

DO NOT

stand directly in front of the vehicle or in the bay when vehicle is being loaded or driven into position.

DO NOT

Go near vehicle or attempt to work on the vehicle when being raised or lowered.

REMAIN CLEAR

of lift

when raising or lowering vehicle.

DO NOT

rock the vehicle while on the lift or remove any heavy components from vehicle that may cause

excessive weight shift.

DO NOT

lower the vehicle until people, materials, and tools are clear

ALWAYS INSURE

that the safeties are engaged before any attempt is made to work on or near vehicle.

Some vehicle maintenance and repair activities may cause the vehicle to shift. Follow the manufacturer’s

guidelines when performing these operations. The use of jack stands or alternate lift points may be required
when completing some repairs.

READ AND UNDERSTAND

all safety warning procedures before operating lift.

KEEP HANDS AND FEET CLEAR

. Remove hands and feet from any moving parts. Keep feet clear of lift when

lowering. Avoid pinch points.

ONLY TRAINED OPERATORS

should operate this lift. All non-trained personnel should be kept away from work area.

Never let non-trained personnel come in contact with, or operate lift.

USE LIFT CORRECTLY

. Use lift in the proper manner. Never use lifting adapters other than what is approved by

the manufacturer.

DO NOT

override self-closing lift controls.

CLEAR AREA

if vehicle is on danger of falling.

STAY ALERT

. Watch what you are doing. Use common sense. Be aware.

CHECK FOR DAMAGED PARTS

. Check for alignment of moving parts, breakage of parts or any condition that

may affect its operation. Do not use lift if any component is broken or damaged.

NEVER

remove safety related components from the lift. Do not use lift if safety related components are

damaged or missing.

When the lift is being lowered, make sure everyone is standing at least six feet away.

Be sure there are no jacks, tools, equipment, left under the lift before lowering.

Always lower the vehicle down slowly and smoothly.

Содержание XP-10AC





















































Результаты поиска

Содержание XP-10AC

Отзывы:

Похожие инструкции для XP-10AC

Бренды по названию

Популярные бренды

BendPak XP-10AC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание XP-10AC

Отзывы:

Похожие инструкции для XP-10AC

Бренды по названию

Популярные бренды