BendPak XP-10AC Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 52

background image

7

INSTALLER / OPERATOR

PLEASE READ AND FULLY

UNDERSTAND.

BY PROCEEDING, YOU AGREE TO

THE FOLLOWING:

I have visually inspected the site where the lift is to be

installed and verified the concrete to be in good condition
and free of cracks or other defects. I understand that
installing a lift on cracked or defective concrete could
cause lift failure resulting in personal injury or death.

I understand that a level floor is required for proper

installation and level lifting.

I understand that I am responsible if my floor is of

questionable slope and that I will be responsible for all
charges related to pouring a new level concrete slab if
required and any charges.

I understand that the lifts are supplied with concrete

fasteners meeting the criteria of the American National
Standard "Automotive Lifts - Safety Requirements for
Construction, Testing, and Validation" ANSI/ALI ALCTV-
1998, and that I will be responsible for all charges related
to any special regional structural and/or seismic anchoring
requirements specified by any other agencies and/or
codes such as the Uniform Building Code (UBC) and/or
International Building Code (IBC).

I will assume full responsibility for the concrete floor

and condition thereof, now or later, where the above
equipment model(s) are to be installed. Failure to follow
danger, warning, and caution instructions may lead to
serious personal injury or death to operator or bystander
or damage to property.

I understand that Bendpak lifts are designed to be

installed in indooor locations only. Failure to follow instal-
lation instructions may lead to serious personal injury or
death to operator or bystander or damage to property or
lift.

Failure to follow danger, warning, and caution

instructions may lead to serious personal injury or death

to operator or bystander or damage to property.

Please read entire manual prior to installation.

Do not operate this machine until you read and

understand all the dangers, warnings and cautions

in this manual. For additional copies

or further information, contact:

BendPak Inc. / Ranger Products

1645 Lemonwood Dr.

Santa Paula, CA. 93060

1-805-933-9970

www.bendpak.com

INSTALLER / OPERATOR

PROTECTIVE EQUIPMENT

Personal protective equipment helps makes installation

and operation safer, however, it does not take the place of

safe operating practices. Always wear durable work

clothing during any installation and/or service activity.

Shop aprons or shop coats may also be worn, however

loose fitting clothing should be avoided. Tight fitting

leather gloves are recommended to protect technician

hands when handling parts. Sturdy leather work shoes

with steel toes and oil resistant soles should be used by

all service personnel to help prevent injury during typical

installation and operation activities.

Eye protection is essential during installation and opera-

tion activities. Safety glasses with side

shields, goggles, or face shields are

acceptable. Back belts provide support

during lifting activities and are also helpful

in providing worker protection.

Consideration should also be given to the

use of hearing protection if service activity is performed in

an enclosed area, or if noise levels are high.

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED

COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS

AND CAN CAUSE PERSONAL INJURY OR DEATH. READ AND FOLLOW ALL INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

«
...
5
6
7
8
9
...
»

Содержание XP-10AC





















































Отзывы:

Нет отзывов

Похожие инструкции для XP-10AC

Бренд: R. Beck Maschinenbau Страницы: 31

Бренд: ShoreStation Страницы: 15

NeverFreeze SX-0810-24

Бренд: ThermoSoft Страницы: 5

Бренд: Chimera Страницы: 14

Бренд: Carel Страницы: 94

Бренд: Redback Страницы: 16

Бренд: Sel Страницы: 12

Бренд: human care Страницы: 24

Бренд: Kabola Страницы: 27

Бренд: R. Beck Maschinenbau Страницы: 31

Бренд: National Instruments Страницы: 265

Бренд: Halfen Страницы: 32

Бренд: Omega Engineering Страницы: 52

Бренд: Schwing Страницы: 48

Бренд: ProMinent Страницы: 2

Бренд: PROMETHEUS Страницы: 39

Бренд: Beckhoff Страницы: 53

Бренд: Barrier Systems Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды