BendPak HD-7500 Series Скачать руководство пользователя страница 61

Страница: 61 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Reviewing the Final Checklist

Make sure these things have been done

before

putting the Lift into service:

•

Review the

Installation Checklist

to make sure all steps have been performed.

•

Make sure the Power Unit is getting power from the power source.

•

Check the Hydraulic Fluid reservoir on the Power Unit; it must be full of approved Hydraulic Fluid or
automatic transmission fluid.

You can damage the motor by running it without enough

fluid.

•

Check the Hydraulic System for leaks.

•

Make sure all four Posts are properly anchored, shimmed, level, and stable.

•

Make sure all Lifting Cables are properly seated in their Sheaves.

•

Make sure all Safety Locks are operating normally.

•

Make sure the backup Slack Safety Locks are

not

engaged.

•

If it has not been done already, perform an Operational Test of the Lift with a typical Vehicle. Refer

Performing an Operational Test

•

Make sure a copy of the

Installation and Operation Manual

is left with the Lift.

Содержание HD-7500 Series




















































































Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды

BendPak HD-7500 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды