BendPak HD-7500 Series Скачать руководство пользователя страница 41

Страница: 41 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Installing the Second End of the Flex Tube

Once the Power Unit is installed, you can install the second end of the Flex Tube (the other end was

connected to the Powerside Runway earlier in the installation).

To install the Flex Tube:

Find the Flex Tube Bracket Plate and the Flex Tube Angle Plate. The Flex Tube is already nearby.

Install the Flex Tube Bracket Plate.

Note

: It is common to install the Flex Tube Bracket Plate between the Mounting Bracket and

the Back Plate. This allows the Zero Angle Bracket (which holds the Pushbutton Air Valve

and is described in the next section) to be installed between the Back Plate and the

retaining Nut. This configuration is common, but it is not required.

Side view of where the Power Unit attaches to the Power Post. Power Unit not shown.

Connect the Flex Tube Angle Plate to the Flex Tube Bracket Plate so that the hole for the Flex

Tube is best positioned for connecting the Return Line, the Air Line, and the Hydraulic Hose.
The Flex Tube Angle Plate can be connected on either side of the Flex Tube Bracket Plate.

When the Flex Tube Angle Plate is in place, unscrew the Plastic Nut from the end of the Flex

Tube.

Holding the Flex Tube by the Plastic Collar, put the Threads through the hole on the Flex Tube
Angle Plate

from underneath

Screw the Plastic Nut back onto the Threads and tighten.

Содержание HD-7500 Series




















































































Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды

BendPak HD-7500 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды