BendPak HD-7500 Series Скачать руководство пользователя страница 14

Страница: 14 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Selecting a Power Post Location

You need to pick a Power Post location now, near the beginning of the installation process, as its

location impacts other aspects of the installation.
You have two options for Power Post location:

Driver-Side Front

Passenger-Side Rear

Note

: The Power Post location decision has no impact on the Approach direction or where the

Front and Rear of the Lift are. It does impact other aspects of the installation, however.

Drawing not necessarily to scale. Not all components shown. Powerside Runway (which has the
Hydraulic Cylinder under it)

must

be installed next to the Power Post, no matter which Power Post

location you choose.

Most customers choose their Power Post location based on either preference (one option makes more

sense for their shop than the other does) or easier access to the power source.

Содержание HD-7500 Series




















































































Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды

BendPak HD-7500 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды