BendPak HD-7500 Series Скачать руководство пользователя страница 40

Страница: 40 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Filling the Hydraulic Fluid Reservoir

The Hydraulic Fluid reservoir on the Power Unit must be filled with Hydraulic Fluid or automatic
transmission fluid before you begin normal operation of the Lift.

When you receive the Lift, the

fluid reservoir is empty.

The Power Unit will

not

work correctly until it is filled with approved Hydraulic Fluid.

Approved fluids are any general purpose ISO-32, ISO-46, or ISO-68 hydraulic fluid, approved

automatic transmission fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, or any synthetic

multi-Vehicle automatic transmission fluid.

⚠

WARNING

Do not run your Power Unit without Hydraulic Fluid; you will damage it.

To fill the Reservoir with Hydraulic Fluid

Remove the Reservoir Cap and set it aside.
Make sure to keep the Reservoir Cap clean; you do not want any contaminants getting into the

Hydraulic Fluid Reservoir.

Fill the Hydraulic Fluid Reservoir on the Power Unit with the appropriate amount of approved

fluids.
The Hydraulic Reservoir holds from 3.5 to 4.5 gallons, depending on your Power Unit:

–

5585280

: 3.7 gallons / 14 liters

–

5585247

: 3.7 gallons / 14 liters

–

5585106

: 3.5 gallons / 13.25 liters

–

5585014

: 3.7 gallons / 14 liters

Use care to keep the fluid clean when filling the reservoir.

Do not connect the Power Unit to a power source at this point.

Replace the Reservoir Cap.

Содержание HD-7500 Series




















































































Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды

BendPak HD-7500 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7500 Series

Отзывы:

Похожие инструкции для HD-7500 Series

Бренды по названию

Популярные бренды