BendPak HD-7500 Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 84

background image

HD-7500 Series Four-Post Lifts

56

P/N 5900174 — Rev. C — March 2021

Boat Trailer Tongue Platform

The Boat Trailer Tongue Platform extends 20 inches, from 48 to 68 inches between the Runways.
The Boat Trailer Tongue Platform can support up to 3,000 lbs.; do

not

exceed the lifting capacity.

To install the Boat Trailer Tongue Platform

:

1.

Locate the Boat Trailer Tongue Platform.

2.

Have two people

carefully

raise the Boat Trailer Platform and orient it appropriately between the

Lift’s two Runways.

3.

Lower the Boat Trailer Platform to just above the Utility Rails, and adjust the Extendable Bases to

the correct width.

4.

Lower the Boat Trailer Platform onto the Utility Rails, making sure that the Extendable Bases are

sitting securely in the Utility Rails.

Gusset Covers

Gusset Covers go on top of the Crosstube Gussets; one per Crosstube. 4 Gusset Covers total.

To install the Gusset Covers

:

1.

Locate the four Plastic Covers from the Parts Box that came with your Lift.

2.

Align the Covers with the openings in the Gusset, one at each end of the Crosstube, then push
the Cover into place.
Do the same for the remaining covers.

«
...
54
55
56
57
58
...
»

Содержание HD-7500 Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для HD-7500 Series

Бренд: IN-COMMAND Страницы: 47

Бренд: Safety Clamps Страницы: 16

Бренд: Wenshing Страницы: 4

Бренд: Ascon tecnologic Страницы: 4

Hardon mini R1271C

Бренд: Caen RFID Страницы: 39

Foxtrot C-IT-0908S

Бренд: TECO Страницы: 4

Бренд: Digitrax Страницы: 8

Бренд: Magneti Marelli Страницы: 44

ZIP CHAIN LIFTER

Бренд: Tsubaki Страницы: 40

Smarty 4X P Series

Бренд: Salda Страницы: 30

Бренд: Gruetzner Страницы: 41

Бренд: Walkera Страницы: 22

Бренд: Denyo Страницы: 30

Бренд: ITR Страницы: 15

Бренд: Contec Страницы: 62

Бренд: Eagle Страницы: 16

Бренд: Miller Electric Страницы: 36

Бренд: FLAIG TE Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды