background image

10

The driver should be especially careful when approaching 

certain types of vehicles or objects.  The Wingman Advanced 

radar may not be able to detect vehicles and objects with 

limited  metal  surfaces  (such  as  recreational  vehicles, 

horse-drawn buggies, motorcycles, logging trailers, etc.).

NOTE: Entering a curve may reduce the alert time to less 
than three (3) seconds.

FIGURE 11 - STATIONARY OBJECT ALERT DISPLAYED

BRAKE OVERUSE ALERT

 The Bendix

®

 Wingman

®

 Advanced

 system provides 

a warning when the system is intervening and using 
the foundation brakes excessively.  Overuse of the 
foundation brakes can lead to the brakes overheating 
and a potential loss of braking performance caused 
by brake fade.  

Using cruise control on downhill runs will 

cause this alert to be activated.

 Approach grades as you would normally, with the 

appropriate gear selected and at a safe speed.  Cruise 
control should NOT
 be used on downhill grades.

When the system detects brake overuse, depending on the 

vehicle manufacturer, a text message will be displayed on 

the dashboard and an audible alert will be activated. The 

driver should intervene immediately.

FIGURE 12 - BRAKE OVERUSE WARNING

•  Once  the  brake  overuse  alert  is  activated,  certain 

driver  interventions  that  cancel  cruise  control  –  like 

stepping on the brake pedal or switching off cruise – will 

discontinue the alert.  Following an overuse alert, the 

driver should not reset cruise control for at least 20 

minutes.  This gives the brakes time to cool down.  If 

the driver chooses to reset cruise control during that 

20  minute  period,  Wingman Advanced  interventions 

will be limited to de-throttling and engine retarder only. 

The  system  will  automatically  disable  all  Wingman 

Advanced system foundation brake applications for at 

least 20 minutes.

•  If the system does not detect a driver intervention within 

15  seconds  after  the  brake  overuse  alert  sounds,  it 

will shut itself off and set a Diagnostic Trouble Code 

(DTC).  The driver will continue to receive alerts, but ALL 

Wingman Advanced interventions (de-throttling, engine 

retarder or brake applications) will be disabled until the 

next ignition cycle.

Note:  In all cases, the driver still has the ability to 
apply the foundation brakes if necessary.  The driver 
should take care since overheated brakes may reduce 
the vehicle’s braking capability.  

(See Appendix F7.0).

1.9  WINGMAN ADVANCED SYSTEM 

DIAGNOSTIC TROUBLE CODES

The Wingman Advanced system is monitored and if any 

malfunction is detected, a Diagnostic Trouble Code (DTC) 

will be set and the driver will be alerted.  The exact alert 

given depends on the vehicle manufacturer: refer to your 

vehicle operator’s manual and Sections 3 and 4.

1.10 RADAR SENSOR INTERCHANGEABILITY

Many  variables  must  be  considered  when  determining 

whether or not the radar sensor can be relocated from one 

vehicle to another vehicle.  They include, but are not limited 

to, the version of the Bendix

®

ESP

®

 stability system used 

on the vehicle, the instrument cluster, the vehicle ECU, the 

engine and the transmission. Contact the Bendix Tech Team 

at 1-800-AIR-BRAKE to determine if this is a viable option.

 WARNING:  Do not interchange radar sensors 

without contacting Bendix fi rst!

1.11 ALERT VOLUME

For Wingman Advanced systems installed on vehicles with 

alerts that come directly through the instrument cluster, 

audible alert levels are pre-set at the factory and can not 

be turned off, nor can the volume be adjusted.  However, 

where  the  Bendix

®

  Driver  Interface  Unit  (DIU)  is  used, 

volume adjustment is permitted.

1.12 POTENTIAL FALSE ALERTS

In certain unusual traffi c or roadway conditions, Wingman 

Advanced may issue a false alert.
Drivers should take into account the road conditions, and 

any other factors they are encountering, as they choose 

how to react to any alerts they receive from the Wingman 

Advanced system.

Содержание Wingman FLR20

































































Отзывы: