background image

8

THE FORWARD VEHICLE DETECTED ICON

When cruise control is switched on and set and a vehicle 

ahead of you is detected by the radar, the detected forward 

vehicle icon — or similar — will illuminate on the vehicle 

dashboard.

This is an indication to the driver that the Bendix

®

 Wingman

®

Advanced

  system  is  actively  managing  the  distance 

between  your  vehicle  and  the  vehicle  ahead,  and  may 

intervene automatically, if needed.

See Figure 6 for examples.

FIGURE 6 - FORWARD VEHICLE DETECTED ICONS

ADJUSTING THE CRUISE CONTROL SPEED

Use the switch(es) provided by the vehicle manufacturer 

to  set  your  cruise  control  speed.    When  adjusted,  your 

set speed will typically be indicated on the vehicle dash, 

message center, or speedometer.

1.6 FOLLOWING DISTANCE

Following  distance  refers  to  the  time  gap,  measured  in 

seconds, between your vehicle and the vehicle ahead.  The 

actual physical distance between the two will vary based 

on the speeds of both vehicles; however, the set gap will 

remain the same for all set cruise speeds.

FOLLOWING DISTANCE 
ADJUSTMENT SWITCH

This  optional  Wingman

®

 Advanced

  feature,  allows  the 

driver to adjust the following distance or time gap.  The 

availability  of  this  feature  is  determined  by  the  vehicle 

manufacturer.  The switch has an increase or decrease 

function.    Pressing  increase  (+)  will  provide  a  larger 

following  distance,  measured  in  seconds.    Pressing 

decrease (-) will provide a shorter following distance.

1.7  WINGMAN ADVANCED COLLISION 

MITIGATION FEATURE OPERATION

Whenever your vehicle is traveling at above 15 mph, the 

Wingman Advanced collision mitigation feature is ready to 

intervene, if needed.  It does not require cruise control to be 

set.  The collision mitigation feature of Wingman Advanced 

will alert you automatically and apply up to two-thirds of the 

vehicle’s braking capacity, if a collision with the detected 

forward vehicle is likely to occur.  You, the driver, must 

immediately act to potentially avoid, or lessen the severity 

of, a collision.
Collision mitigation is ready to intervene as long as no DTCs 

are active in either the brake system, Wingman Advanced 

system, or any other contributing vehicle system.

AUTOMATIC FOUNDATION 
BRAKE APPLICATIONS

The  vehicle  automatically  manages  foundation  braking 

priorities  among  the  various  vehicle  systems  that  use 

the  foundation  brakes,  such  as  Wingman Advanced, 

Bendix

®

 ESP

®

 (Electronic Stability Program), Bendix

®

ATC 

(Automatic Traction Control) and the Bendix

®

 ABS (Antilock 

Braking System).

1.8 ALERTS AND WARNINGS

The Bendix Wingman Advanced system operates differently 

compared to other cruise control/forward collision warning 

systems.  It is important for 

YOU

 to fully understand the 

system’s features, especially the driver alerts and warnings.
Three  important  warnings  provided  by  the  Wingman 

Advanced system are the Following Distance Alert (FDA), 

Impact Alert (IA), and Stationary Object Alert (SOA).  The 

driver will be alerted by any of the three warnings, whether 

or not the cruise control is activated.

See Appendix F, Sections 3.0-5.0, for more information 
about how DIUs communicate alerts.

 

WARNING:  Any audible and/or visual alert by the 

system means that your vehicle is too close to the 
vehicle ahead and the driver must immediately act to 
potentially avoid, or lessen the severity of, a collision.

Содержание Wingman FLR20

































































Отзывы: