background image

9

IMPACT ALERT (IA)

 The Impact Alert is the most severe warning issued 

by the Bendix

®

 Wingman

®

 Advanced

 system.  This 

alert indicates that a collision with the detected forward 
vehicle is likely and the driver must immediately act to 
potentially avoid, or lessen the severity of, a collision.

The Impact Alert is ready to alert the driver whenever 
the vehicle is moving above 15 mph.

When activated, the IA will sound and a visual message/

icon typically appears on the dash screen or Bendix

®

 Driver 

Interface  Unit  (DIU)  display.   The  actual  sound/display 

method varies by vehicle manufacturer.

NOTE:  The Impact Alert is typically accompanied by 
automatic brake interventions.  The Wingman Advanced 
system will apply up to two-thirds of your vehicle’s braking 
capacity.  The driver must apply additional braking, when 
necessary, to maintain a safe distance from the vehicle 
ahead.

See Figure 7 for an example of an Impact Alert Icon.

FIGURE 7 - EXAMPLE OF IMPACT ALERT ICON

FIGURE 8 - IMPACT ALERT TEXT AND LIGHT PATTERN AS 
SEEN ON THE BENDIX

®

 DIU

FOLLOWING DISTANCE ALERT (FDA)

 The Following Distance Alert (FDA) provides both 

audible and visual alerts whenever the time between 
your vehicle and the detected forward vehicle ahead is 
less than one and a half (1.5) seconds* and decreasing.  
Once the audible alert is given, the driver should 
increase the distance 
between his/her vehicle 
and the vehicle ahead 
until the audible alert 
stops.

The  FDA  is  ready  to  alert 

the  driver  whenever  the 

vehicle  is  moving  above 

fi ve (5) mph.  If the following 

distance continues to 

decrease, the driver will hear 

more  rapid  audible  alerts. 

When the FDA reaches its 

highest level, typically a red 

LED also illuminates on the 

instrument cluster.  The FDA 

may be accompanied by a 

visual alert.
* 1.5 seconds is the system 

default  and  may  vary  by 

fl eet/OEM.

Above: Examples of other vehicle

manufacturer’s displays.

FIGURE 10 - FOLLOWING DISTANCE ALERT

STATIONARY OBJECT ALERT (SOA)

 Stationary Object Alert (SOA) – The Bendix

® 

Wingman

®

 Advanced

 system will give up to a three (3) 

second alert to the driver when approaching a detected, 
sizable, metallic (radar-refl ective), stationary object in 
your lane of travel.  This alert indicates that a collision 
with a stationary object is likely and the driver must 
immediately act to potentially avoid, or lessen the 
severity of, a collision.

The SOA is ready to alert the driver whenever the vehicle 

is moving above ten (10) mph.

FIGURE 9 -  DRIVER 
INTERFACE UNIT (DIU) 
SHOWING EXAMPLES 
OF FOLLOWING 
DISTANCE ALERTS WITH 
PROGRESSIVELY FASTER 
AUDIBLE ALERTS.

Содержание Wingman FLR20

































































Отзывы: